Toss PIREG-C2 - 1 General, Safety and Warning Instructions; Note on the Device Description

16502 PIREG-C2 Gerätebeschreibung mit EtherNet_IP Bussystem191017 - EN.docx/ Page 2 of 66
2
4.7.8. FESP command 22
4.7.9. FEZU command 23
4.7.10. GADR command 24
4.7.11. GTYP command 24
4.7.12. GWPA command 24
4.7.13. HZBG command 25
4.7.14. ISTW command 25
4.7.15. KANR command 26
4.7.16. KAPA command 26
4.7.17. KAPK command 27
4.7.18. KASR command 28
4.7.19. KOKO command 28
4.7.20. KONF command 29
4.7.21. KOUE command 30
4.7.22. KPFK command 30
4.7.23. KTKZ command 31
4.7.24. MEPA command 31
4.7.25. PFUE command 32
4.7.26. SOLW command 32
4.7.27. STEU command 33
4.7.28. STKA command 33
4.7.29. STRS command 34
4.7.30. STST command 34
4.7.31. TKEI command 34
4.7.32. TKEK command 35
4.7.33. TOKG command 35
4.7.34. TUEE command 36
4.7.35. UIMW command 36
4.7.36. VERS command 37
4.7.37. WESE command 37
4.7.38. ZUST command 38
4.7.39. ZYKL command 39
4.8. EtherNet/IP communication 41
4.9. Device data 41
4.10. Process data 42
4.10.1. Read process data, T  O 42
4.10.2. Write process data, O  T 42
4.10.3. Configuration parameters 43
4.11. Parameter data 43
4.11.1. AHUE parameter data 43
4.11.2. BSTZ parameter data 44
4.11.3. EINS parameter data 44
4.11.4. EIPA parameter data 45
4.11.5. FEKO Parameterdaten 46
4.11.6. GWPA parameter data 46
4.11.7. HZBG parameter data 46
4.11.8. KAPK parameter data 47
4.11.9. KASR parameter data 48
4.11.10. KONF parameter data 48
4.11.11. KPFK parameter data 49
4.11.12. KTKZ parameter data 50
4.11.13. PFUE parameter data 50
4.11.14. TKEK parameter data 50
4.11.15. TOKG parameter data 52
4.11.16. TUEE parameter data 53
4.11.17. VERS parameter data 53
4.11.18. WESE parameter data 53
4.11.19. ZYKL parameter data 54
4.12. EtherNet/IP reset 56
4.12.1 Power-on reset 56
4.12.2 Factory settings 56
4.13. Manual IP address 56
5. Installation and commissioning 57
5.1. Installation 57
5.2. 120/240V mains voltage changeover 57
5.3. Configuring the settings 57
5.4. Connecting the PIREG-C2 58
5.5. Control inputs 58
5.6. Connecting to the mains voltage 58
5.7. Burning in the heating conductor 58
5.8. When the contr. does not work corr. 58
6. The heating conductor 58
7. Technical data 60
7.1. Controller 60
7.2. Current transformer 62
7.3. Potentiometer 63
7.4. Analogue display 63
7.5. Sealing transformer 63
7.6. TM6 thermometer 63
7.7. Ordering codes 63
7.8 Housing 64
7.8.1. PIREG-C2 housing 64
7.8.2. Current transformer housing 64
7.8.3. Potentiometer housing 64
7.8.4. Analogue display housing 64
7.9. Spare parts 64
8. Connection diagrams 65
8.1. PIREG-C2 with ext. solid-state relay 65
8.2. PIREG-C2 with internal thyristors 65
8.3. RS232 / RS485 connection - interface 65
9. Application note 66
9.1. Application instructions 66
10. Disposal 66
1. General, safety and warning instructions
1.1. Note on the device description
The purpose of this device description is to ensure optimum installation, commissioning, operation and
maintenance of the PIREG-C2 and must be read prior to carrying out any of the actions described. Keep
the device description handy and accessible to all users for possible referencing. Pass this manual on to
future users of the PIREG-C2.
All necessary settings are described in this device description. Should difficulties nevertheless arise dur-
ing commissioning or operation, please do not carry out any unauthorised manipulations. You could put
yourself and others at risk as well as jeopardize your warranty claim. In such cases, please contact us
immediately:
GmbH & Co. KG Phone: +49 (0) 64 08 - 90 91 - 0
-Verpackungssysteme- Fax: +49 (0) 64 08 - 43 55
Danziger Straße 15 E-mail: info@toss-gmbh.de
D-35418 Alten-Buseck Internet: www.toss-gmbh.de