EasyManuals Logo

TRENDnet TEW-718BRM User Manual

TRENDnet TEW-718BRM
73 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #36 background imageLoading...
Page #36 background image
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-718BRM
33
Review the outbound packet filter settings.
Source IPEnter the source IP address or computer/device IP address on your
local network to apply the filter. (e.g. 192.168.10.101)
Destination IP : PortsEnter the destination IP address of the
computer/device located on the Internet and port number to apply the filter.
To specify all port numbers, do not specify any value for Ports field. For specific
port numbers, enter a port number or range within the range of 1-65535 (e.g.
21 or 21-30) in the Ports field.
Note: Typically, you can specify 0.0.0.0 for any destination IP address located on
the Internet or enter the specific IP address. (e.g. 10.10.10.200)
Protocol Select the protocol type to filter. TCP, UDP, or you can select Both
to choose both protocol types.
EnableCheck the option to enable the filter.
Use rule# - Click the drop-down list to select a pre-defined schedule. The filter
will only be active during the time period defined in the pre-defined schedule.
Note: Before applying scheduling, please ensure your Time settings are configured
correct and you have defined a schedule. See page 36
to configure Time Settings and see
page 48 to create a schedule.
Click Apply at the bottom of the page to save the changes.
Note: If you would like to discard the changes, click Undo before you click Apply.
Clicking MAC Level will bring you to the MAC Filter configuration page. See MAC Filter
section.
Inbound Packet Filter
You may want apply inbound packet filters to allow or deny access of specific traffic
from the Internet to computers or devices on your local network.
To configure inbound packet filters:
Click Inbound Filter at the bottom of the outbound packet filter page.
Next to Inbound Packet Filter, check the Enable option to enable inbound filtering.
Select Allow all to pass except those match the following rules to allow all
traffic and deny only the filters specified in the list.
Select Deny all to pass except those match the following rules to deny all
traffic and allow only the filter specified in the list.
Review the inbound packet filter settings.
Source IPEnter the source IP address or computer/device IP address on your
located on the Internet to apply the filter. (e.g. 192.168.10.101)
Note: Typically, you can specify 0.0.0.0 for any source IP address located on the
Internet or enter the specific IP address. (e.g. 10.10.10.200)
Destination IP : PortsEnter the destination IP address of the
computer/device located on your local network and port number to apply the
filter. To specify all port numbers, do not specify any value for Ports field. For

Table of Contents

Other manuals for TRENDnet TEW-718BRM

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TRENDnet TEW-718BRM and is the answer not in the manual?

TRENDnet TEW-718BRM Specifications

General IconGeneral
Ethernet LANYes
Cabling technology10/100Base-T(X)
Networking standardsIEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1p, IEEE 802.1Q, IEEE 802.3, IEEE 802.3u
Ethernet LAN data rates10, 100 Mbit/s
Ethernet LAN interface typeFast Ethernet
Modulation16-QAM, 64-QAM, BPSK, CCK, DBPSK, DQPSK, OFDM, QPSK
Wi-Fi standards802.11b, 802.11g, Wi-Fi 4 (802.11n)
Channels quantity13 channels
Top Wi-Fi standardWi-Fi 4 (802.11n)
WLAN data transfer rate (max)150 Mbit/s
Rack mountingNo
Frequency band2.4 GHz
Frequency range2.4 - 2.4835 GHz
WLAN data transfer rates supported11, 54, 150 Mbit/s
Ethernet LAN (RJ-45) ports4
DSL specificationG.992.1, G.992.2, G.992.3, G.992.5
DHCP client-
Routing protocolsIGRP, IP, RIP-1, RIP-2
Security algorithms128-bit WEP, 64-bit WEP, WPA, WPA-PSK, WPA2-PSK
Antennas quantity1
CertificationCE, FCC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (typical)5 W
Storage temperature (T-T)-10 - 70 °C
Operating temperature (T-T)0 - 40 °C
Product colorBlack
LED indicatorsDSL, LAN, WLAN
Weight and Dimensions IconWeight and Dimensions
Depth189 mm
Width118 mm
Height33 mm
Weight221 g

Related product manuals