WAGO SYSTEM 750 - 1 Notes about this Documentation; Validity of this Documentation; Revision History; Table 1: Variants

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-493 3-Phase Power Measurement Module
Manual
Version 1.2.0
Pos: 7 /Al le Ser ien ( All ge mein e M odul e)/Ü ber sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume ntat ion /Hi nw eise zu dies er D o kume ntati on - Ü b erschr if t 1 @ 4 \mod_1237987661750_21.docx @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Al le Ser ien ( All ge mein e M odul e)/H in weis e z ur D oku men tati on/H in weis e/Hi n weis : Do kum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos: 9 /Al le Ser ien ( All ge mein e M odul e)/Ü ber sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume ntat ion /G ültig keit sb erei ch - Ü b erschr if t 2 @ 12\mod_1338912448776_21.docx @ 96469 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Hi n weise z ur Do kum ent ati on/G ülti gkei ts berei ch/ Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 7 50- xxx x, S tan dar dversi on un d au fgel ist et e Vari ant en @ 14\mod_1358944038682_21.docx @ 109354 @ @ 1
This documentation is only applicable to the I/O module 750-493 (3-Phase Power
Measurement Module) and the variants listed in the table below.
Pos: 11 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Hi n weise z ur Do kum ent ati on/G ülti gkei ts berei ch/ Var iant enl ist en/ Var iant enli st e - 7 50-49 3 - Standardversionen 1A+5A und erw.Temp. /025- @ 23\mod_1433851670418_21.docx @ 183628 @ @ 1
Table 1: Variants
Item Number
Description
750-493
3-Phase Power Measurement Module 1 A
750-493/000-001
3-Phase Power Measurement Module 5 A
750-493/025-000
3-Phase Power Measurement Module 1 A,
Operating temperature -20 °C … +60 °C
750-493/025-001
3-Phase Power Measurement Module 5A,
Operating temperature -20 °C … +60 °C
Pos: 12 /Al l e Ser ien (Al lg emei ne M od ule)/H i nweis e zur D o kume ntati on /Hin wei se/H in weis : G ülti g keit d er Anga ben für aufg el iste te V ari ant en @ 9\mod_1281520778141_21.docx @ 63085 @ @ 1
Documentation Validity for Variants
Unless otherwise indicated, the information given in this documentation applies to
listed variants.
Pos: 13 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Hi n weise z ur Do kum ent ati on/Hi nw eise /Ac htu ng: H in weis z ur Do ku ment ati on B uskl emm en 75 0-xxxx @ 4\ mod_1237986979656_21.docx @ 29023 @ @ 1
The I/O module 750-493 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 14 /Alle Seri en ( All ge mein e Mo dule) /Ü ber schr if ten f ür alle Ser ie n/Hin wei se z ur D o kume ntat ion/ Än deru ngs his tori e - Üb ersc hrift 2 @ 6\ mod_1255513312687_21. docx @ 42790 @ 2 @ 1
1.2 Revision History
Pos: 15 /S eri e 7 50 ( WA GO-I/O- SYST EM) /Hi n weise z ur Do kum ent ati on/Ä nder ung shis tori e/B uskl emme n/Ä nder ung shis tori e -493 @ 13\mod_1346246064669_21.docx @ 102093 @ @ 1