What to do if the safety thermostat has tripped on my Windhager FireWIN Boiler?
If the safety thermostat has tripped on your Windhager Boiler, it means the boiler temperature is above 100 °C, causing the boiler to enter burnout mode. You should check the water level or pressure in the heating system and refill or bleed the air as necessary.
Why is the combustion chamber pressure not stable in my Windhager FireWIN Boiler?
If your Windhager Boiler's combustion chamber pressure is not stable, it could be due to several reasons: * Heating surface cover leaking: Check whether it is firmly closed. * Combustion chamber and ash door leaking: Check the seal and renew it if necessary. * Pressure measuring nipple blocked: Clear it. * Intake air line or induction opening blocked: Clear it. * Exhaust pipe or flue blocked: Clear it. * Combustion chamber pressure switch defective.
Why is the reserve supply container empty on my Windhager FireWIN Boiler?
If your Windhager Boiler indicates that the reserve supply container is empty, it is because the feed is outside the enable time. Extend the enable time for the feed in the 'Feed operating mode' menu item.
What to do if Windhager Boiler displays 'Reserve supply container empty'?
If your Windhager Boiler displays 'Reserve supply container empty', it means that the reserve supply container is empty. Fill fuel into the fuel container.
What to do if the cladding door is open on my Windhager Boiler?
If the cladding door is open on your Windhager Boiler, the burner will be locked. Close the cladding door to resolve this.
What to do if there is no flame formation in control mode in Windhager FireWIN?
If your Windhager Boiler displays 'No flame formation in control mode', it means that the flame goes out in modulation mode. Clean the burner and the boiler.
Why is my Windhager FireWIN Boiler feed not sucking any pellets in?
If your Windhager Boiler is not sucking any pellets, it could be due to a few reasons: * No pellets at the suction wand: Set 'Wand switching' to 'automated' or select another wand. * Feed hose blocked: Clear it.
How to troubleshoot no display on InfoWIN for Windhager Boiler?
If you are getting a 'No display on InfoWIN' error with your Windhager Boiler, here are a few things to check: 1. Electricity: Ensure the cable is properly connected and check the building fuse. 2. Device fuse: Check the device fuse and replace it if necessary. 3. InfoWIN plug: Make sure the plug is firmly connected. It's located on the side at the top behind the right side panel cladding.
What to do for excess temperature in the auger tube in Windhager Boiler?
If you encounter 'Excess temperature in the auger tube' on your Windhager Boiler, the boiler switches to burnout mode. Check the burner and remove all pellets from the burner pot.
What to do if there is no negative pressure in the combustion chamber of my Windhager Boiler?
If you are experiencing 'No negative pressure in the combustion chamber' with your Windhager Boiler, the boiler switches to burnout mode. Check if the heating surface cover is leaking and ensure it is firmly closed.
Details on caution symbols and safety instructions for operation.
Identifies potential hazards like fire, power failure, and burner pot issues.
Explains various operational modes like OFF, ON, Pellet feed, and Solid fuel/buffer.
Provides a summary of cleaning and ash removal intervals for different FireWIN models.
Covers cleaning procedures for the combustion chamber and burner pot.
Troubleshooting steps for when the InfoWINplus display is not working.
Explains common IN messages related to pellet supply and boiler status.
Details FE messages related to auger, feed, probe switching, and pressure.
Covers AL messages related to ash removal, auger, fan, air intake, and safety switches.
To Next Page
General
