4
-14
tionary autotuning1 again and run the motor using the aforementioned procedure under the recommended
conditions or perform stationary autotuning 2 or rotational autotuning.
Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current
for a general-purpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio
of the no-load current to the rated current become. Use the data given in Factory Settings that Change with the
Inverter Capacity (o2-04) of Chapter 5 User Constants as a reference.
Set the autotuning type.
1. Power will be supplied to the motor when stationary autotuning 1 is performed even though the motor
will not turn. Do not touch the motor until autotuning has been completed.
2. When performing stationary autotuning 1 connected to a conveyor or other machine, ensure that the
holding brake is not activated during autotuning.
Step Digital Operator Display
1 Turn ON the power supply.
2
Press the MENU Key several times to access the autotuning display.
The autotuning display will not appear during operation or when a fault
has occurred.
3
Press the DATA/ENTER Key to display the T1-01 (Autotuning Mode
Selection) user constant setting.
4 Press the DATA/ENTER Key to display the current set value of T1-01.
5 Press the Increment Key and set the value to 1 (stationary autotuning 1).
6 Press the DATA/ENTER Key to confirm the value.
㻲㼞㼑㼝㼡㼑㼚㼏㼥㻌㻾㼑㼒
㻙㻰㻾㻵㼂㻱㻙
㼁㻝㻙㻜㻞㻩㻌㻌㻜㻚㻜㻜㻴㼦
㼁㻝㻙㻜㻟㻩㻌㻌㻜㻚㻜㻜㻭
㻾㼐㼥
8 +]
Initial display
㻖㻖㻌㻹㼍㼕㼚㻌㻹㼑㼚㼡㻌㻖㻖
㻙㻭㻚㼀㼁㻺㻱㻙
㻭㼡㼠㼛㻙㼀㼡㼚㼕㼚㼓
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7
㻿㼠㼍㼚㼐㼍㼞㼐㻌㼀㼡㼚㼕㼚㼓
㻎㻜㻎
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7
㻿㼠㼍㼚㼐㼍㼞㼐㻌㼀㼡㼚㼕㼚㼓
㻎㻜㻎
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7
㼀㼡㼚㼑㻙㻺㼛㻌㻾㼛㼠㼍㼠㼑㻝
㻎㻜㻎
Display when the setting has been confirmed
Display after the setting has been confirmed
㻙㻭㻚㼀㼁㻺㻱㻙
㻱㼚㼠㼞㼥㻌㻭㼏㼏㼑㼜㼠㼑㼐
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7
㼀㼡㼚㼑㻙㻺㼛㻌㻾㼛㼠㼍㼠㼑㻝
㻎㻜㻎
TOE-S616-60.1.book 14 ページ ２０１７年８月４日 金曜日 午後３時４１分
To Next Page
Loading...
