YASKAWA Varispeed G7 Series User Manual

Trial Operation Procedures
4- 21
Enter the motor nameplate data.
When the autotuning type has been selected, enter the motor information based on the motor nameplate data.
Repeat steps 1 to 4 and enter the set values for the following user constants.
T1-03 (Motor Rated Voltage)
T1-04 (Motor Rated Current)
T1-05 (Motor Base Frequency)
T1-06 (Number of Motor Poles)
T1-07 (Motor Base Speed)
T1-08 (Number of PG Pulses when Turning): This user constant is only displayed for flux vector control.
T1-09 (Motor No-load Current)
Refer to Table 4.2 Constant Settings before Autotuning for details on the settings.
Step Digital Operator Display
1 Press the Increment Key to display T1-02 (Motor Output Power).
2 Press the DATA/ENTER Key to display the current set value of T1-02.
3
Set the output power of the motor in kilowatts.
Press the Increment or Decrement Key to enter a numeric value.
Press the RESET Key to move the cursor to the digit to enter.
4 Press the DATA/ENTER Key to confirm the value.
㻹㼠㼞㻌㻾㼍㼠㼑㼐㻌㻼㼛㼣㼑㼞
㻙㻭㻚㼀㼁㻺㻱㻙
7 
㻔㻜㻚㻜㻜䡚㻢㻡㻜㻚㻜㻜㻕
㻎㻜㻚㻠㻜㼗㼃㻎
N:
㻙㻭㻚㼀㼁㻺㻱㻙
7

㻔㻜㻚㻜㻜䡚㻢㻡㻜㻚㻜㻜㻕
㻎㻜㻚㻠㻜㼗㼃㻎
㻹㼠㼞㻌㻾㼍㼠㼑㼐㻌㻼㼛㼣㼑㼞
N:

㻙㻭㻚㼀㼁㻺㻱㻙
7

㻔㻜㻚㻜㻜䡚㻢㻡㻜㻚㻜㻜㻕
㻎㻜㻚㻠㻜㼗㼃㻎
㻹㼠㼞㻌㻾㼍㼠㼑㼐㻌㻼㼛㼣㼑㼞
N:

Display when the setting has been confirmed
Display after the setting has been confirmed
㻙㻭㻚㼀㼁㻺㻱㻙
㻱㼚㼠㼞㼥㻌㻭㼏㼏㼑㼜㼠㼑㼐
㻹㼠㼞㻌㻾㼍㼠㼑㼐㻌㻼㼛㼣㼑㼞
㻙㻭㻚㼀㼁㻺㻱㻙
7 
㻔㻜㻚㻜㻜䡚㻢㻡㻜㻚㻜㻜㻕
㻎㻜㻚㻠㻜㼗㼃㻎
N:
TOE-S616-60.1.book 21 ページ ２０１７年８月４日 金曜日 午後３時４１分

YASKAWA Varispeed G7 Series Specifications

General

Brand	YASKAWA
Model	Varispeed G7 Series
Category	Inverter
Language	English