YOKOGAWA DLM2000 Series - Page 104

5-71
IM 710105-17E
Commands
1
2
3
4
5
6
App
Index
:ANALysis:PMEAsure<x>:MEASure:<Param
eter>:STATe
Function Queries the on/off status of the power
measurement parameter.
Syntax
:ANALysis:PMEAsure<x>:MEASure:<Parame
ter>:STATe {<Boolean>}
:ANALysis:PMEAsure<x>:MEASure:<Parame
ter>:STATe?
<x> = 1 to 2
<Parameter> =
{AH|AHABs|AHN|AHP|IAC|
IAVGfreq|IDC|IMN|INPeak|IPPeak|
IPTopeak|IRMN|IRMS|LAMBda|P|Q|S|UAC|
UAVGfreq|UDC|UMN|UNPeak|UPPeak|
UPTopeak|URMN|URMS|WH|WHABs|WHN|WHP|
Z}
Example
:ANALYSIS:PMEASURE1:MEASURE:AH:STA
TE ON
:ANALYSIS:PMEASURE1:MEASURE:AH:STATE?
-> :ANALYSIS:PMEASURE1:MEASURE:AH:STA
TE 1
:ANALysis:PMEAsure<x>:MEASure:<Param
eter>:VALue?
Function Queries an automatically measured value of a
power measurement parameter.
Syntax
:ANALysis:PMEAsure<x>:MEASure:<Parame
ter>:VALue?
<x> = 1 to 2
<Parameter> =
{AH|AHABs|AHN|AHP|IAC|
IAVGfreq|IDC|IMN|INPeak|IPPeak|
IPTopeak|IRMN|IRMS|LAMBda|P|Q|S|UAC|
UAVGfreq|UDC|UMN|UNPeak|UPPeak|
UPTopeak|URMN|URMS|WH|WHABs|WHN|WHP|
Z}
Example
:ANALYSIS:PMEASURE1:MEASURE:AH:VALUE?
:ANALysis:PMEAsure<x>:MEASure:ALL
Function Collectively turns on or off the power measurement
parameter.
Syntax
:ANALysis:PMEAsure<x>:MEASure:ALL {<B
oolean>}
<x> = 1 to 2
Example
:ANALYSIS:PMEASURE1:MEASURE:ALL ON
:ANALysis:PMEAsure<x>:MODE
Function Sets or queries the on/off status of power
measurement.
Syntax
:ANALysis:PMEAsure<x>:MODE {<Boolean>
}
:ANALysis:PMEAsure<x>:MODE?
<x> = 1 to 2
Example
:ANALYSIS:PMEASURE1:MODE ON
:ANALYSIS:PMEASURE1:MODE?
-> :ANALYSIS:PMEASURE1:MODE 1
:ANALysis:PMEAsure<x>:RANGe
Function Sets or queries the measurement source window.
Syntax
:ANALysis:PMEAsure<x>:RANGe {MAIN|
Z1|Z2}
:ANALysis:PMEAsure<x>:RANGe?
<x> = 1 to 2
Example
:ANALYSIS:PMEASURE1:RANGE MAIN
:ANALYSIS:PMEASURE1:RANGE?
-> :ANALYSIS:PMEASURE1:RANGE MAIN
:ANALysis:PMEAsure<x>:SETup?
Function Queries all power measurement input settings.
Syntax
:ANALysis:PMEAsure<x>:SETup?
<x> = 1 to 2
Example
:ANALYSIS:PMEASURE1:SETUP?
:ANALysis:PMEAsure<x>:SETup:ADESkew
Function Executes auto deskewing for power measurement.
Syntax
:ANALysis:PMEAsure<x>:SETup:ADESkew
<x> = 1 to 2
Example
:ANALYSIS:PMEASURE1:SETUP:ADESKEW
:ANALysis:PMEAsure<x>:SETup:I?
Function Queries all current input channel settings for
power measurement.
Syntax
:ANALysis:PMEAsure<x>:SETup:I?
<x> = 1 to 2
Example
:ANALYSIS:PMEASURE1:SETUP:I?
:ANALysis:PMEAsure<x>:SETup:I:DESKew
Function Set or queries auto deskewing of the current input
channel for power measurement.
Syntax
:ANALysis:PMEAsure<x>:SETup:I:DESK
ew {<Time>}
:ANALysis:PMEAsure<x>:SETup:I:DESKew?
<x> = 1 to 2
<Time>=−100.0nsto100.0ns(in10-pssteps)
Example
:ANALYSIS:PMEASURE1:SETUP:I:DESK
EW 1NS
:ANALYSIS:PMEASURE1:SETUP:I:DESKEW?
-> :ANALYSIS:PMEASURE1:SETUP:I:DESK
EW1.000E−09
5.3 ANALysis Group