YOKOGAWA DLM2000 Series - Page 119

5-86
IM 710105-17E
:CURSor[:TY]:MARKer:M<x>:JUMP
Function Makes a marker cursor in the T-Y display jump to
the specified zoom waveform.
Syntax
:CURSor[:TY]:MARKer:M<x>:JUMP {Z1|Z2}
<x> = 1 to 4
Example
:CURSOR:TY:MARKER:M1:JUMP Z1
Description Jumps to the center of the zoom waveform.
:CURSor[:TY]:MARKer:M<x>:POSition
Function Sets or queries the time value of a marker cursor.
Syntax
:CURSor[:TY]:MARKer:M<x>:POSition {<N
Rf>}
:CURSor[:TY]:MARKer:M<x>:POSition?
<x> = 1 to 4
<NRf>=−5to5(instepsof10divisions/display
record length)
Example
:CURSOR:TY:MARKER:M1:POSITION−1
:CURSOR:TY:MARKER:M1:POSITION?
-> :CURSOR:TY:MARKER:M1:POSITION−1.0
000000
:CURSor[:TY]:MARKer:M<x>:T?
Function Queries all time axis settings for a marker cursor.
Syntax
:CURSor[:TY]:MARKer:M<x>:T?
<x> = 1 to 4
:CURSor[:TY]:MARKer:M<x>:T:STATe
Function Sets or queries the on/off status of the time value
of a marker cursor.
Syntax
:CURSor[:TY]:MARKer:M<x>:T:STA
Te {<Boolean>}
:CURSor[:TY]:MARKer:M<x>:T:STATe?
<x> = 1 to 4
Example
:CURSOR:TY:MARKER:M1:T:STATE ON
:CURSOR:TY:MARKER:M1:T:STATE?
-> :CURSOR:TY:MARKER:M1:T:STATE 1
:CURSor[:TY]:MARKer:M<x>:T:VALue?
Function Queries the time value of a marker cursor.
Syntax
:CURSor[:TY]:MARKer:M<x>:T:VALue?
<x> = 1 to 4
Example
:CURSOR:TY:MARKER:M1:T:VALUE?
-> :CURSOR:TY:MARKER:M1:T:VALUE−4.50
00E−03
:CURSor[:TY]:MARKer:M<x>:DT<x>:STATe
Function Sets or queries the on/off status of the time value
measured between marker cursors.
Syntax
:CURSor[:TY]:MARKer:M<x>:DT<x>:STA
Te {<Boolean>}
:CURSor[:TY]:MARKer:M<x>:DT<x>:STATe?
<x> = 1 to 4
<y> = 1 to 4
Example
:CURSOR:TY:MARKER:M:DT1:STATE ON
:CURSOR:TY:MARKER:M:DT1:STATE?
-> :CURSOR:TY:MARKER:M:DT1:STATE 1
:CURSor[:TY]:MARKer:M<x>:DT<x>:VAL
ue?
Function Queries the time value between marker cursors.
Syntax
:CURSor[:TY]:MARKer:M<x>:DT<x>:VALue?
<x> = 1 to 4
<y> = 1 to 4
Example
:CURSOR:TY:MARKER:M:DT1:VALUE?
-> :CURSOR:TY:MARKER:M:DT1:VALUE 0.00
00000E+00
:CURSor[:TY]:MARKer:M<x>:DV<x>?
Function Queries all of the settings related to vertical-axis
measurement between marker cursors.
Syntax
:CURSor[:TY]:MARKer:M<x>:DV<x>?
<x> = 1 to 4
<y> = 1 to 4
:CURSor[:TY]:MARKer:M<x>:DV<x>:STATe
Function Sets or queries the on/off status of the vertical
value measured between marker cursors.
Syntax
:CURSor[:TY]:MARKer:M<x>:DV<x>:STA
Te {<Boolean>}
:CURSor[:TY]:MARKer:M<x>:DV<x>:STATe?
<x> = 1 to 4
<y> = 1 to 4
Example
:CURSOR:TY:MARKER:M:DV1:STATE ON
:CURSOR:TY:MARKER:M:DV1:STATE?
-> :CURSOR:TY:MARKER:M:DV1:STATE 1
:CURSor[:TY]:MARKer:M<x>:DV<y>:VAL
ue?
Function Queries the vertical value between marker
cursors.
Syntax
:CURSor[:TY]:MARKer:M<x>:DV<x>:VALue?
<x> = 1 to 4
<y> = 1 to 4
Example
:CURSOR:TY:MARKER:M:DV1:VALUE?
-> :CURSOR:TY:MARKER:M:DV1:VALUE 500.
00000E−03
Description When linear scaling is on, the DLM2000 returns
the scaled value.
5.9 CURSor Group