5-97
IM 710105-17E
Commands
5
:FFT<x>:MEASure:PEAK[:BASic]:V<y>:VA
Lue?
Function Queries a peak value for FFT analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:V<y>:VAL
ue?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
Example
:FFT1:MEASURE:PEAK:BASIC:V1:VALUE?
-> :FFT1:MEASURE:PEAK:BASIC:V1:
VALUE 1.000E+00
:FFT<x>:MODE
Function Sets or queries the waveform display mode for
FFT analysis.
Syntax
:FFT<x>:MODE {AVERage|MAXHold|NORMal}
:FFT<x>:MODE?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:MODE AVERAGE
:FFT1:MODE?
-> :FFT1:MODE AVERAGE
:FFT<x>:RANGe
Function Sets or queries the measurement source window
for FFT analysis.
Syntax
:FFT<x>:RANGe {MAIN|Z1|Z2}
:FFT<x>:RANGe?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:RANGE MAIN
:FFT1:RANGE?
-> :FFT1:RANGE MAIN
:FFT<x>:RPOSition
Function Sets or queries the center point for magnifying the
vertical axis for FFT analysis.
Syntax
:FFT<x>:RPOSition {<NRf>}
:FFT<x>:RPOSition?
<x> = 1 or 2 (1 only for 2-channel models)
<NRf>=−4to4(divisions)
Example
:FFT1:RPOSITION 1
:FFT1:RPOSITION?
-> :FFT1:RPOSITION 1.000E+00
:FFT<x>:TRACe
Function Sets or queries the source waveform for FFT
analysis.
Syntax
:FFT<x>:TRACe {<NRf>|MATH<x>}
:FFT<x>:TRACe?
<x> of FFT<x> = 1 or 2 (1 only for 2-channel
models)
<NRf> = 1 to 4 (1 or 2 for 2-channel models)
<x> of MATH<x> = 1 or 2 (1 only for 2-channel
models)
Example
:FFT1:TRACE 1
:FFT1:TRACE?
-> :FFT1:TRACE 1
:FFT<x>:MEASure:PEAK[:BASic]:FREQuen
cy<y>:VALue?
Function Queries a peak frequency value for FFT analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:FREQuenc
y<y>:VALue?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
Example
:FFT1:MEASURE:PEAK:BASIC:FREQUENCY1:V
ALUE?
-> :FFT1:MEASURE:PEAK:BASIC:FREQUENCY
1:VALUE 1.000E+00
:FFT<x>:MEASure:PEAK[:BASic]:RANGe
<y>
Function Sets or queries the measurement range of a peak
value for FFT analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:RANGe
<y> {<NRf>}
:FFT<x>:MEASure:PEAK[:BASic]:RANGe
<y>?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
<NRf>=−5to5(divisions)
Example
:FFT1:MEASURE:PEAK:BASIC:RANGE1 0,1
:FFT1:MEASURE:PEAK:BASIC:RANGE1?
-> :FFT1:MEASURE:PEAK:BASIC:RANGE1 1.
000E+00,0.000E+00
:FFT<x>:MEASure:PEAK[:BASic]:V<y>?
Function Queries all of the settings for a peak value for FFT
analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:V<y>?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
:FFT<x>:MEASure:PEAK[:BASic]:V<y>:ST
ATe
Function Sets or queries the on/off status of a peak value
for FFT analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:V<y>:STA
Te {<Boolean>}
:FFT<x>:MEASure:PEAK[:BASic]:V<y>:STA
Te?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
Example
:FFT1:MEASURE:PEAK:BASIC:V1:STATE ON
:FFT1:MEASURE:PEAK:BASIC:V1:STATE?
-> :FFT1:MEASURE:PEAK:BASIC:V1:
STATE 1
5.11 FFT Group
To Next Page
Loading...
Need help?
General
