YOKOGAWA DLM2000 Series - Page 181

5-148
IM 710105-17E
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:HYSTeresis
Function Sets or queries a source waveform hysteresis for
state or state width searching.
Syntax
:SEARch:PPATtern:{CHANnel<x>|
MATH<x>}:HYSTeresis {<NRf>}
:SEARch:PPATtern:{CHANnel<x>|
MATH<x>}:HYSTeresis?
<x> of CHANnel<x> = 1 to 4 (1 or 2 for 2-channel
models)
<x> of MATH<x> = 1 or 2 (1 only for 2-channel
models)
<NRf> = 0.3 to 4 divisions in 0.1 steps
Example
:SEARCH:PPATTERN:CHANNEL1:HYSTERES
IS 0.3
:SEARCH:PPATTERN:CHANNEL1:HYSTERESIS?
-> :SEARCH:PPATTERN:CHANNEL1:HYSTERES
IS 0.30
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:LEVel
Function Sets or queries a source waveform search level
for state or state width searching.
Syntax
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:LEVel {<NRf>|<Voltage>}
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:LEVel?
<x> of CHANnel<x> = 1 to 4 (1 or 2 for 2-channel
models)
<x> of MATH<x> = 1 or 2 (1 only for 2-channel
models)
<NRf> = See the DLM2000 Features Guide for
this information.
Example
:SEARCH:PPATTERN:CHANNEL1:LEVEL 1V
:SEARCH:PPATTERN:CHANNEL1:LEVEL?
-> :SEARCH:PPATTERN:CHANNEL1:LEVEL 1.
000E+00
Description When the probe type is set to current, this
command sets or queries the <Current> value.
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:PATTern
Function Sets or queries a source waveform search pattern
for state or state width searching.
Syntax
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:PATTern {DONTcare|HIGH|LOW}
:SEARch:PPATtern:{CHANnel<x>|MATH<x>
}:PATTern?
<x> of CHANnel<x> = 1 to 4 (1 or 2 for 2-channel
models)
<x> of MATH<x> = 1 or 2 (1 only for 2-channel
models)
Example
:SEARCH:PPATTERN:CHANNEL1:PATTERN HIG
H
:SEARCH:PPATTERN:CHANNEL1:PATTERN?
-> :SEARCH:PPATTERN:CHANNEL1:
PATTERN HIGH
:SEARch:PPATtern:CLOCk?
Function Queries all clock channel settings for state or state
width searching.
Syntax
:SEARch:PPATtern:CLOCk?
:SEARch:PPATtern:CLOCk:HYSTeresis
Function Sets or queries the clock channel hysteresis for
state or state width searching.
Syntax
:SEARch:PPATtern:CLOCk:HYSTeresis {<N
Rf>}
:SEARch:PPATtern:CLOCk:HYSTeresis?
<NRf> = 0.3 to 4 divisions in 0.1 steps
Example
:SEARCH:PPATTERN:CLOCK:HYSTERESIS 4.0
:SEARCH:PPATTERN:CLOCK:HYSTERESIS?
-> :SEARCH:PPATTERN:CLOCK:
HYSTERESIS 4.00
Description If
:SEARch:PPATtern:CLOCk:SOURce
is set to
NONE, an error occurs.
:SEARch:PPATtern:CLOCk:LEVel
Function Sets or queries the clock channel search level for
state or state width searching.
Syntax
:SEARch:PPATtern:CLOCk:LEVel {<NRf>|<
Voltage>}
:SEARch:PPATtern:CLOCk:LEVel?
<NRf> = See the DLM2000 Features Guide for
this information.
Example
:SEARCH:PPATTERN:CLOCK:LEVEL
:SEARCH:PPATTERN:CLOCK:LEVEL?
-> :SEARCH:PPATTERN:CLOCK:LEVEL
Description • If
:SEARch:PPATtern:CLOCk:SOURce
is set
to NONE, an error occurs.
• When the probe type is set to current, this
command sets or queries the <Current> value.
5.23 SEARch Group