YOKOGAWA DLM2000 Series - Page 189

5-156
IM 710105-17E
:SERialbus<x>:CAN:SEARch:SETup[:IDDa
ta]:DATA:DECimal<y>
Function Sets a reference value, which is one of the ID and
data conditions, for CAN bus signal searching in
decimal notation.
Syntax
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:DECimal<y> {<NRf>,<NRf>}
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:DECimal<y>?
<x> = 1 to 4
<y> = 1 or 2
<NRf> = See the DLM2000 Features Guide for
this information.
Example
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:DECIMAL1 1
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:DECIMAL1?
-> :SERIALBUS1:CAN:SEARCH:SETUP:IDDAT
A:DATA:DECIMAL1 1
:SERialbus<x>:CAN:SEARch:SETup[:IDDa
ta]:DATA:DLC
Function Sets or queries the data length code (DLC), which
is one of the ID and data conditions, for CAN bus
signal searching.
Syntax
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:DLC {<NRf>}
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:DLC?
<x> = 1 to 4
<NRf> = 0 to 8
Example
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:DLC 0
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:DLC?
-> :SERIALBUS1:CAN:SEARCH:SETUP:IDDAT
A:DATA:DLC 0
:SERialbus<x>:CAN:SEARch:SETup[:IDDa
ta]:DATA:ENDian
Function Sets or queries the byte order of the reference
values, which is one of the ID and data conditions,
for CAN bus signal searching.
Syntax
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:ENDian {BIG|LITTle}
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:ENDian?
<x> = 1 to 4
Example
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:ENDIAN BIG
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:ENDIAN?
-> :SERIALBUS1:CAN:SEARCH:SETUP:IDDAT
A:DATA:ENDIAN BIG
:SERialbus<x>:CAN:SEARch:SETup[:IDDa
ta]:DATA:HEXa<y>
Function Sets a reference value, which is one of the ID and
data conditions, for CAN bus signal searching in
hexadecimal notation.
Syntax
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:HEXa<y> {<String>}
<x> = 1 to 4
<y> = 1 to 8
Example
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:HEXA1 "12"
:SERialbus<x>:CAN:SEARch:SETup[:IDDa
ta]:DATA:MODE
Function Sets or queries the data enable/disable condition,
which is one of the ID and data conditions, for
CAN bus signal searching.
Syntax
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:MODE {<Boolean>}
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:MODE ON
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:MODE?
-> :SERIALBUS1:CAN:SEARCH:SETUP:IDDAT
A:DATA:MODE 1
:SERialbus<x>:CAN:SEARch:SETup[:IDDa
ta]:DATA:MSBLsb
Function Sets or queries the MSB and LSB bits for the data,
which is one of the ID and data conditions, for
CAN bus signal searching.
Syntax
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:MSBLsb {<NRf>,<NRf>}
:SERialbus<x>:CAN:SEARch:SETup[:IDDat
a]:DATA:MSBLsb?
<x> = 1 to 4
<NRf> = 0 to 63
Example
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:MSBLSB 1,0
:SERIALBUS1:CAN:SEARCH:SETUP:IDDATA:D
ATA:MSBLSB?
-> :SERIALBUS1:CAN:SEARCH:SETUP:IDDAT
A:DATA:MSBLSB 1,0
5.24 SERialbus Group