YOKOGAWA DLM2000 Series - Page 198

5-165
IM 710105-17E
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:DATA:MODE
Function Sets or queries the data enable/disable condition,
which is one of the ID and data conditions, for
CAN FD bus signal searching.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:MODE {<Boolean>}
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:MODE ON
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:MODE?
-> :SERIALBUS1:CANFD:SEARCH:SETUP:IDD
ATA:DATA:MODE 1
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:DATA:MSBLsb
Function Sets or queries the MSB and LSB bits for the
data, which is one of the ID and data conditions,
for CAN FD bus signal searching.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:MSBLsb {<NRf>,<NRf>}
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:MSBLsb?
<x> = 1 to 4
<NRf> = 0 to 63
Example
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:MSBLSB 15,0
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:MSBLSB?
-> :SERIALBUS1:CANFD:SEARCH:SETUP:IDD
ATA:DATA:MSBLSB 15,0
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:DATA:PATTern<y>
Function Sets or queries the data value, which is one of
the ID and data conditions, for CAN FD bus signal
searching in binary notation.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:PATTern<y> {<String>}
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:PATTern<y>?
<x> = 1 to 4
<y> = 1 to 8
Example
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:PATTERN1 "00110101"
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:PATTERN1?
-> :SERIALBUS1:CANFD:SEARCH:SETUP:IDD
ATA:DATA:PATTERN1 "00110101"
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:DATA:PFORmat
Function Sets or queries the data input format, which is one
of the ID and data conditions, for CAN FD bus
signal searching.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:PFORmat {BINary|HEXa}
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:PFORmat?
<x> = 1 to 4
Example
:SERIALBUS1:CANFD:SEARCH:SETUP:IDDATA
:DATA:PFORMAT BINARY
:SERIALBUS1:CANFD:SEARCH:SETUP:IDDATA
:DATA:PFORMAT?
-> :SERIALBUS1:CANFD:SEARCH:SETUP:IDD
ATA:DATA:PFORMAT BINARY
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:DATA:SIGN
Function Sets or queries whether signed or unsigned data
format will be used, which is one of the ID and
data conditions, for CAN FD bus signal searching.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:SIGN {SIGN|UNSign}
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:DATA:SIGN?
<x> = 1 to 4
Example
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:SIGN SIGN
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:DATA:SIGN?
-> :SERIALBUS1:CANFD:SEARCH:SETUP:IDD
ATA:DATA:SIGN SIGN
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:IDENtifier?
Function Queries all identifier settings for the ID and data
conditions for CAN FD bus signal searching.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:IDENtifier?
<x> = 1 to 4
:SERialbus<x>:CANFD:SEARch:SETup[:ID
Data]:IDENtifier:HEXa
Function Sets the ID value, which is one of the ID and data
conditions, for CAN FD bus signal searching in
hexadecimal notation.
Syntax
:SERialbus<x>:CANFD:SEARch:SETup[:IDD
ata]:IDENtifier:HEXa {<String>}
<x> = 1 to 4
Example
:SERIALBUS1:CANFD:SEARCH:SETUP:
IDDATA:IDENTIFIER:HEXA "1AB"
5.24 SERialbus Group