YOKOGAWA DLM2000 Series - Page 204

5-171
IM 710105-17E
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:FLEXray:SEARch:SETup:E
RRor:HCRC
Function Sets or queries the FLEXRAY bus signal search
Header CRC error setting.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup:ER
Ror:HCRC {<Boolean>}
:SERialbus<x>:FLEXray:SEARch:SETup:ER
Ror:HCRC?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:ERRO
R:HCRC ON
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:ERRO
R:HCRC?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:E
RROR:HCRC 1
:SERialbus<x>:FLEXray:SEARch:SETup:I
DData?
Function Queries all ID and data condition settings for
FLEXRAY bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup:ID
Data?
<x> = 1 to 4
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt?
Function Queries all cycle-count settings for FLEXRAY bus
signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt?
<x> = 1 to 4
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt:CONDition
Function Sets or queries the cycle-count data-condition
settings for FLEXRAY bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:CONDition {BETWeen|EQUa
l|GREater|LESS|NOTBetween|NOTEqul}
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:CONDition?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:CCOUNT:CONDITION BETWEEN
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:CCOUNT:CONDITION?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:I
DDATA:CCOUNT:CONDITION BETWEEN
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt:COUNt<y>
Function Sets or queries a FLEXRAY bus signal-search
cycle-count setting.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:COUNt<y> {<NRf>}
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:COUNt<y>?
<x> = 1 to 4
<y> = 1 or 2
<NRf> = 0 to 63
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:CCOUNT:COUNT1 10
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:CCOUNT:COUNT1?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:I
DDATA:CCOUNT:COUNT1 10
Description • For :SERialbus<x>:FLEXray:SEARch
:SETup[:IDData]:CCOunt:CONDition
EQUal|GREater|NOTEqul, set the cycle-count
setting using :SERialbus<x>:FLEXray:SEARch:
SETup[:IDData]:CCOunt:COUNt1.
• For :SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:CONDition LESS, set the cycle-
count setting using :SERialbus<x>:FLEXray:SE
ARch:SETup[:IDData]:CCOunt:COUNt2.
• For :SERialbus<x>:FLEXray:SEARch
:SETup[:IDData]:CCOunt:CONDition
BETWeen|NOTBetween, set the smaller value
using :SERialbus<x>:FLEXray:SEARch:SETu
p[:IDData]:CCOunt:COUNt1, and set the larger
value using :SERialbus<x>:FLEXray:SEARch:S
ETup[:IDData]:CCOunt:COUNt2.
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt:MODE
Function Sets or queries the cycle-count mode, which is
one of the ID and data conditions, for FLEXRAY
bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:MODE {<Boolean>}
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:CCOunt:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:CCOUNT:MODE ON
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:CCOUNT:MODE?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:I
DDATA:CCOUNT:MODE 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA?
Function Queries all ID and data condition settings for
FLEXRAY bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:DATA?
<x> = 1 to 4
5.24 SERialbus Group