YOKOGAWA DLM2000 Series - Page 221

5-188
IM 710105-17E
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:EDETection
Function Sets or queries the error detection method for
PSI5 signal analysis.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:EDETection {CRC|PARity}
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:EDETection?
<x> = 1 to 4
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:E
DETECTION CRC
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:E
DETECTION?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DAT
A:EDETECTION CRC
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:SNRejection
Function Queries all PSI5 signal analysis noise rejection
settings.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SNRejection?
<x> = 1 to 4
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:SNRejection:ETIMe
Function Sets or queries the rejection end time for PSI5
signal analysis noise rejection.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SNRejection:ETIMe
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SNRejection:ETIMe?
<x> = 1 to 4
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:S
NREJECTION:ETIME 66.0000E-06
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:S
NREJECTION:ETIME?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DAT
A:SNREJECTION:ETIME 66.0000E-6
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:SNRejection:MODE
Function Sets or queries the on/off status of the PSI5 signal
analysis noise rejection.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SNRejection:MODE
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SNRejection:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:S
NREJECTION:MODE 1
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:S
NREJECTION:MODE?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DAT
A:SNREJECTION:MODE 1
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:SOURce
Function Sets or queries the data source for PSI5 signal
analysis.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SOURce {<NRf>|MATH<y>}
:SERialbus<x>:PSI5[:ANALyze]:SETup:DA
TA:SOURce?
<x> = 1 to 4
<y> = 1 or 2
<NRf> = 1 to 4
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:S
OURCE 1
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:S
OURCE?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DAT
A:SOURCE 1
:SERialbus<x>:PSI5[:ANALyze]:SETup:N
UMBerofslot
Function Sets or queries the number of slots for PSI5 signal
analysis.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:NU
MBerofslot {AUTO|<NRf>}
:SERialbus<x>:PSI5[:ANALyze]:SETup:NU
MBerofslot?
<x> = 1 to 4
<NRf> = 1 to 6
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:NUMBER
OFSLOT AUTO
:SERIALBUS1:PSI5:ANALYZE:SETUP:NUMBER
OFSLOT?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:NUM
BEROFSLOT AUTO
5.24 SERialbus Group