YOKOGAWA DLM2000 Series User Manual

5-218
IM 710105-17E
:SERialbus<x>:TYPE
Function Sets or queries search type.
Syntax
:SERialbus<x>:TYPE {CANFDbus|CANBus|F
LEXray|I2CBus|LINBus|PSI5|SENT|SPATte
rn|SPIBus|UART}
:SERialbus<x>:TYPE?
<x> = 1 to 4 (1 only for 2-channel models)
Example
:SERIALBUS1:TYPE CANBUS
:SERIALBUS1:TYPE?
-> :SERIALBUS1:TYPE CANBUS
:SERialbus<x>:UART?
Function Queries all UART signal analysis and search
settings.
Syntax
:SERialbus<x>:UART?
<x> = 1 to 4
:SERialbus<x>:UART[:ANALyze]?
Function Queries all UART signal analysis settings.
Syntax
:SERialbus<x>:UART[:ANALyze]?
<x> = 1 to 4
:SERialbus<x>:UART[:ANALyze]:SETup?
Function Queries all UART signal analysis bus settings.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup?
<x> = 1 to 4
:SERialbus<x>:UART[:ANALyze]:SETup:B
ITorder
Function Sets or queries the UART signal analysis bit order.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:BI
Torder {MSBFirst|LSBFirst}
:SERialbus<x>:UART[:ANALyze]:SETup:BI
Torder?
<x> = 1 to 4
Example
:SERIALBUS1:UART:ANALYZE:SETUP:BITORD
ER MSBFIRST
:SERIALBUS1:UART:ANALYZE:SETUP:BITORD
ER?
-> :SERIALBUS1:UART:ANALYZE:SETUP:BIT
ORDER MSBFIRST
:SERialbus<x>:UART[:ANALyze]:SETup:B
RATe
Function Sets or queries the UART signal analysis bit rate
(data transfer rate).
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:BR
ATe {<NRf>|USER,<NRf>}
:SERialbus<x>:UART[:ANALyze]:SETup:BR
ATe?
<x> = 1 to 4
<NRf> = 1200, 2400, 4800, 9600, 19200
USER <NRf> = See the DLM2000 Features Guide
for this information.
Example
:SERIALBUS1:UART:ANALYZE:SETUP:BRA
TE 2400
:SERIALBUS1:UART:ANALYZE:SETUP:BRATE?
-> :SERIALBUS1:UART:ANALYZE:SETUP:BRA
TE 2400
:SERialbus<x>:UART[:ANALyze]:SETup:B
SPace
Function Sets or queries the byte space setting for UART
signal analysis.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:BS
Pace {<Time>}
:SERialbus<x>:UART[:ANALyze]:SETup:BS
Pace?
<x> = 1 to 4
<Time> = See the DLM2000 Features Guide for
this information.
Example
:SERIALBUS1:UART:ANALYZE:SETUP:BSPA
CE 0.1S
:SERIALBUS1:UART:ANALYZE:SETUP:BSPA
CE?
-> :SERIALBUS1:UART:ANALYZE:SETUP:BSP
ACE1.000E−01
:SERialbus<x>:UART[:ANALyze]:SETup:G
ROuping
Function Sets or queries the on/off status of grouping for
UART signal analysis.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:GR
Ouping {<Boolean>}
:SERialbus<x>:UART[:ANALyze]:SETup:GR
Ouping?
<x> = 1 to 4
Example
:SERIALBUS1:UART:ANALYZE:SETUP:GROUPI
NG ON
:SERIALBUS1:UART:ANALYZE:SETUP:GROUPI
NG?
-> :SERIALBUS1:UART:ANALYZE:SETUP:GRO
UPING 1
5.24 SERialbus Group

YOKOGAWA DLM2000 Series Specifications

General

Brand	YOKOGAWA
Model	DLM2000 Series
Category	Test Equipment
Language	English