YOKOGAWA DLM2000 Series - Page 303

5-270
IM 710105-17E
:TRIGger[:ATRigger]:CANFD:MODE
Function Sets or queries the CAN FD bus signal trigger
mode.
Syntax
:TRIGger[:ATRigger]:CANFD:MODE {EFRam
e|ID|IDOR|SOF}
:TRIGger[:ATRigger]:CANFD:MODE?
Example
:TRIGGER:ATRIGGER:CANFD:MODE EFRAME
:TRIGGER:ATRIGGER:CANFD:MODE?
-> :TRIGGER:ATRIGGER:CANFD:MODE EFRAM
E
:TRIGger[:ATRigger]:CANFD:RECessive
Function Sets or queries the CAN FD bus signal trigger
recessive level.
Syntax
:TRIGger[:ATRigger]:CANFD:RECessi
ve {HIGH|LOW}
:TRIGger[:ATRigger]:CANFD:RECessive?
Example
:TRIGGER:ATRIGGER:CANFD:RECESSIVE HIG
H
:TRIGGER:ATRIGGER:CANFD:RECESSIVE?
-> :TRIGGER:ATRIGGER:CANFD:RECESSIVE
HIGH
:TRIGger[:ATRigger]:CANFD:SOURce
Function Sets or queries the CAN FD bus signal trigger
signal.
Syntax
:TRIGger[:ATRigger]:CANFD:SOUR
ce {<NRf>}
:TRIGger[:ATRigger]:CANFD:SOURce?
<NRf> = 1 to 4
Example
:TRIGGER:ATRIGGER:CANFD:SOURCE 1
:TRIGGER:ATRIGGER:CANFD:SOURCE?
-> :TRIGGER:ATRIGGER:CANFD:SOURCE 1
:TRIGger[:ATRigger]:CANFD:SPOint
Function Sets or queries the CAN FD bus signal trigger
sample point.
Syntax
:TRIGger[:ATRigger]:CANFD:SPOi
nt {<NRf>}
:TRIGger[:ATRigger]:CANFD:SPOint?
<NRf> = 18.8 to 90.6 (resolution:0.1)
Example
:TRIGGER:ATRIGGER:CANFD:SPOINT 75
:TRIGGER:ATRIGGER:CANFD:SPOINT?
-> :TRIGGER:ATRIGGER:CANFD:SPOINT 75.
00000000
:TRIGger[:ATRigger]:OR?
Function Queries all edge OR trigger settings.
Syntax
:TRIGger[:ATRigger]:OR?
:TRIGger[:ATRigger]:OR:CHANnel<x>
Function Sets or queries the edge of a channel for edge OR
triggering.
Syntax
:TRIGger[:ATRigger]:OR:
CHANnel<x> {OFF|RISE|FALL|IN|OUT}
:TRIGger[:ATRigger]:OR:CHANnel<x>?
<x> = 1 to 4
Example
:TRIGGER:ATRIGGER:OR:CHANNEL1 RISE
:TRIGGER:ATRIGGER:OR:CHANNEL1?
-> :TRIGGER:ATRIGGER:OR:CHANNEL1 RISE
Description Select
{IN|OUT}
when
:TRIGger:OR:WINDow
ON
is specified. Select
{FALL|RISE}
otherwise.
:TRIGger[:ATRigger]:PSI5?
Function Queries all PSI5 signal trigger settings.
Syntax
:TRIGger[:ATRigger]:PSI5?
:TRIGger[:ATRigger]:PSI5:DATA?
Function Queries all PSI5 signal trigger data settings.
Syntax
:TRIGger[:ATRigger]:PSI5:DATA?
:TRIGger[:ATRigger]:PSI5:DATA:CONDit
ion
Function Sets or queries the data condition for PSI5 signal
triggering.
Syntax
:TRIGger[:ATRigger]:PSI5:DATA:CONDiti
on {EQUal|TRUE}
:TRIGger[:ATRigger]:PSI5:DATA:CONDiti
on?
Example
:TRIGGER:ATRIGGER:PSI5:DATA:CONDITI
ON EQUAL
:TRIGGER:ATRIGGER:PSI5:DATA:CONDITI
ON?
-> :TRIGGER:ATRIGGER:PSI5:DATA:CONDIT
ION EQUAL
:TRIGger[:ATRigger]:PSI5:DATA:DECim
al
Function Sets or queries the data for PSI5 signal triggering
in decimal notation.
Syntax
:TRIGger[:ATRigger]:PSI5:DATA:DECim
al {<NRf>}
:TRIGger[:ATRigger]:PSI5:DATA:DECim
al?
 When<NRf>=10bitdata,−512to511
 16bitdata,−32768to32767
Example
:TRIGGER:ATRIGGER:PSI5:DATA:DECIM
AL−10
:TRIGGER:ATRIGGER:PSI5:DATA:DECIMAL?
-> :TRIGGER:ATRIGGER:PSI5:DATA:DECIM
AL−10
Description This command is valid when
:TRIGger[:ATRig
ger]:PSI5:DATA:CONDition
is
EQUal
.
5.33 TRIGger Group