YOKOGAWA DLM4038 - Page 103

5-70
IM DLM4038-17EN
:ANALysis:PANalyze<x>:SOA:CURSor:Y<y
>:VALue?
Function Sets or queries the voltage value of a vertical
cursor in the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:CURSor:Y<y
>:VALue?
Example
:ANALYSIS:PANALYZE1:SOA:CURSOR:Y1:VA
LUE?
-> :ANALYSIS:PANALYZE1:SOA:CURSOR:Y1
:VALUE 1.000E+00
:ANALysis:PANalyze<x>:SOA:MODE
Function Sets or queries the automated measurement
mode of the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:MODE {CURS
or|OFF}
:ANALysis:PANalyze<x>:SOA:MODE?
<x> = 1 to 2
Example
:ANALYSIS:PANALYZE1:SOA:MODE CURSOR
:ANALYSIS:PANALYZE1:SOA:MODE?
-> :ANALYSIS:PANALYZE1:SOA:MODE CURS
OR
:ANALysis:PANalyze<x>:SOA:TRANge
(Time Range)
Function Sets or queries the range of the T-Y waveform to
display in the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:TRAN
ge {<NRf>,<NRf>}
:ANALysis:PANalyze<x>:SOA:TRANge?
<x> = 1 to 2
<NRf> = −5 to 5 divisions (in steps of 10
divisions/display record length)
Example
 :ANALYSIS:PANALYZE1:SOA:TRANGE−4,4
:ANALYSIS:PANALYZE1:SOA:TRANGE?
-> :ANALYSIS:PANALYZE1:SOA:TRANG
E−4.00,4.00
:ANALysis:PANalyze<x>:SOA:VTDisplay
Function Sets or queries whether or not to display the VT
waveform in the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:VTDispl
ay {<Boolean>}
:ANALysis:PANalyze<x>:SOA:VTDisplay?
<x> = 1 to 2
Example
:ANALYSIS:PANALYZE1:SOA:VTDISPLAY ON
:ANALYSIS:PANALYZE1:SOA:VTDISPLAY?
-> :ANALYSIS:PANALYZE1:SOA:VTDISPLA
Y 1
:ANALysis:PANalyze<x>:SWLoss?
Function Queries all switching loss settings.
Syntax
:ANALysis:PANalyze<x>:SWLoss?
<x> = 1 to 2
Description Use the commands listed below to set the
reference levels (distal, mesial, proximal, etc.)
used to determine the total loss.
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxi
mal?
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxi
mal:MODE
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxi
mal:PERCent
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxi
mal:UNIT
:MEASure:{CHANnel<x>|MATH<x>}:METHod
:ANALysis:PANalyze<x>:SWLoss:CYCLe
Function Sets or queries the on/off status of cycle mode.
Syntax
:ANALysis:PANalyze<x>:SWLoss:CYC
Le {<Boolean>}
:ANALysis:PANalyze<x>:SWLoss:CYCLe?
<x> = 1 to 2
Example
:ANALYSIS:PANALYZE1:SWLOSS:CYCLE ON
:ANALYSIS:PANALYZE1:SWLOSS:CYCLE?
-> :ANALYSIS:PANALYZE1:SWLOSS:CYC
LE 1
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al?
Function Queries all distal, mesial, and proximal settings.
Syntax
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al?
Example
:ANALYSIS:PANALYZE1:SWLOSS:DPROXIM
AL?
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al:MODE
Function Sets or queries the distal, mesial, and proximal
point mode setting.
Syntax
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al:MODE {PERCent|UNIT}
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al:MODE?
Example
:ANALYSIS:PANALYZE1:SWLOSS:
DPROXIMAL:MODE PERCENT
:ANALYSIS:PANALYZE1:SWLOSS:
DPROXIMAL:MODE?
-> :ANALYSIS:PANALYZE1:SWLOSS:DPROXI
MAL:MODE PERCENT
5.3 ANALysis Group