YOKOGAWA DLM4038 - Page 197

5-164
IM DLM4038-17EN
:SERialbus<x>:CANFD[:ANALyze]:SETup:
BRATe
Function Sets or queries the CAN FD bus signal analysis
bit rate (data transfer rate).
Syntax
:SERialbus<x>:CANFD[:ANALyze]:SETup:
BRATe {<NRf>|USER,<NRf>}
:SERialbus<x>:CANFD[:ANALyze]:SETup:
BRATe?
<x> = 1 to 4
<NRf> = 250000, 500000, 1000000
USER <NRf> = 20000 to 1000000 (resolution:100)
Example
:SERIALBUS1:CANFD:ANALYZE:SETUP:BRA
TE 1000000
:SERIALBUS1:CANFD:ANALYZE:SETUP:BRA
TE?
-> :SERIALBUS1:CANFD:ANALYZE:SETUP:B
RATE 1000000
:SERialbus<x>:CANFD[:ANALyze]:SETup:
DBRate
Function Sets or queries the CAN FD bus signal analysis
data bit rate (data transfer rate of data phase).
Syntax
:SERialbus<x>:CANFD[:ANALyze]:SETup:
DBRate {<NRf>|USER,<NRf>}
:SERialbus<x>:CANFD[:ANALyze]:SETup:
DBRate?
<x> = 1 to 4
<NRf> = 500000, 1000000, 2000000, 4000000,
5000000, 8000000
USER <NRf> = 250000 to 10000000 (resolution:100)
Example
:SERIALBUS1:CANFD:ANALYZE:SETUP:DBRA
TE 5000000
:SERIALBUS1:CANFD:ANALYZE:SETUP:DBRA
TE?
-> :SERIALBUS1:CANFD:ANALYZE:SETUP:D
BRATE 5000000
:SERialbus<x>:CANFD[:ANALyze]:SETup:
DSPoint
Function Sets or queries the CAN FD bus signal analysis
data phase sample point.
Syntax
:SERialbus<x>:CANFD[:ANALyze]:SETup:
DSPoint {<NRf>}
:SERialbus<x>:CANFD[:ANALyze]:SETup:
DSPoint?
<x> = 1 to 4
<NRf> = 18.8 to 90.6 (resolution:0.1)
Example
:SERIALBUS1:CANFD:ANALYZE:SETUP:DSPO
INT 75
:SERIALBUS1:CANFD:ANALYZE:SETUP:DSPO
INT?
-> :SERIALBUS1:CANFD:ANALYZE:SETUP:D
SPOINT 75.00000000
:SERialbus<x>:CANFD[:ANALyze]:SETup:
FDSTandard
Function Sets or queries whether the CAN FD bus signal
to be analyzed is an ISO standard signal.
Syntax
:SERialbus<x>:CANFD[:ANALyze]:SETup:
FDSTandard {ISO|NISO}
:SERialbus<x>:CANFD[:ANALyze]:SETup:
FDSTandard?
<x> = 1 to 4
Example
:SERIALBUS1:CANFD:ANALYZE:SETUP:FDST
ANDARD ISO
:SERIALBUS1:CANFD:ANALYZE:SETUP:FDST
ANDARD?
-> :SERIALBUS1:CANFD:ANALYZE:SETUP:F
DSTANDARD ISO
:SERialbus<x>:CANFD[:ANALyze]:SETup:
RECessive
Function Sets or queries the CAN FD bus signal analysis
recessive level.
Syntax
:SERialbus<x>:CANFD[:ANALyze]:SETup:
RECessive {HIGH|LOW}
:SERialbus<x>:CANFD[:ANALyze]:SETup:
RECessive?
<x> = 1 to 4
Example
:SERIALBUS1:CANFD:ANALYZE:SETUP:RECE
SSIVE HIGH
:SERIALBUS1:CANFD:ANALYZE:SETUP:RECE
SSIVE?
-> :SERIALBUS1:CANFD:ANALYZE:SETUP:R
ECESSIVE HIGH
:SERialbus<x>:CANFD[:ANALyze]:SETup:
SOURce
Function Sets or queries the CAN FD bus signal analysis
source.
Syntax
:SERialbus<x>:CANFD[:ANALyze]:SETup:
SOURce {<NRf>|MATH<y>}
:SERialbus<x>:CANFD[:ANALyze]:SETup:
SOURce?
<x> = 1 to 4
<NRf> = 1 to 8
<y> of MATH<y> = 1 to 4
Example
:SERIALBUS1:CANFD:ANALYZE:SETUP:SOUR
CE 1
:SERIALBUS1:CANFD:ANALYZE:SETUP:SOUR
CE?
-> :SERIALBUS1:CANFD:ANALYZE:SETUP:S
OURCE 1
5.25 SERialbus Group