YOKOGAWA DLM4038 - Page 217

5-184
IM DLM4038-17EN
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt:MODE
Function Sets or queries the cycle-count mode, which is
one of the ID and data conditions, for FlexRay
bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt:MODE {<Boolean>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:CCOunt:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:CCOUNT:MODE ON
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:CCOUNT:MODE?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:CCOUNT:MODE 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA?
Function Queries all ID and data condition settings for
FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA?
<x> = 1 to 4
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:BCOunt
Function Sets or queries the position for comparing
data patterns, which is one of the ID and data
conditions, for FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:BCOunt {<NRf>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:BCOunt?
<x> = 1 to 4
<NRf> = 0 to 253
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:BCOUNT 1
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:BCOUNT?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:BCOUNT 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:CONDition
Function Sets or queries the comparison condition, which
is one of the ID and data conditions, for FlexRay
bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:CONDition {BETWeen|EQUa
l|FALSe|GREater|LESS|NOTBetween|NOTE
qul|TRUE}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:CONDition?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:CONDITION BETWEEN
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:CONDITION?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:CONDITION BETWEEN
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:DBYTe
Function Sets or queries the number of data bytes, which
is one of the ID and data conditions, for FlexRay
bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:DBYTe {<NRf>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:DBYTe?
<x> = 1 to 4
<NRf> = 1 to 8
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:DBYTE 1
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:DBYTE?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:DBYTE 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:DECimal<y>
Function Sets or queries a reference value, which is one of
the ID and data conditions, for FlexRay bus signal
searching in decimal notation.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:DECimal<y> {<NRf>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:DECimal<y>?
<x> = 1 to 4
<y> = 1 to 2
<NRf> = See the DLM4000 Features Guide for
this information.
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:DECIMAL1 1
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:DECIMAL1?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:DECIMAL1 1.000E+00
5.25 SERialbus Group