YOKOGAWA DLM4038 - Page 218

5-185
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:ENDian
Function Sets or queries the byte order of the reference
values, which is one of the ID and data
conditions, for FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:ENDian {BIG|LITTle}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:ENDian?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:ENDIAN BIG
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:ENDIAN?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:ENDIAN BIG
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:HEXa<y>
Function Sets a reference value, which is one of the ID and
data conditions, for FlexRay bus signal searching
in hexadecimal notation.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:HEXa<y> {<String>}
<x> = 1 to 4
<y> = 1 to 8
<String> = Two characters (each representing
a byte). Each character can be X or a
hexadecimal value from 0 to F
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:HEXA1 "1F"
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:MODE
Function Sets or queries the data enable/disable condition,
which is one of the ID and data conditions, for
FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:MODE {<Boolean>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:MODE ON
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:MODE?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:MODE 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:MSBLsb
Function Sets or queries the MSB and LSB bits for the
data, which is one of the ID and data conditions,
for FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:MSBLsb {<NRf>,<NRf>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:MSBLsb?
<x> = 1 to 4
<NRf> = 0 to 63
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:MSBLSB 7,0
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:MSBLSB?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:MSBLSB 7,0
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:PATTern<y>
Function Sets or queries the data value, which is one of
the ID and data conditions, for FlexRay bus signal
searching in binary notation.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:PATTern<y> {<String>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:PATTern<y>?
<x> = 1 to 4
<y> = 1 to 8
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:PATTERN1 "00001010"
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:PATTERN1?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:PATTERN1 "00001010"
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:PFORmat
Function Sets or queries the data input format, which is
one of the ID and data conditions, for FlexRay
bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:PFORmat {BINary|HEXa}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:PFORmat?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:PFORMAT BINARY
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:PFORMAT?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:PFORMAT BINARY
5.25 SERialbus Group