YOKOGAWA DLM4038 - Page 219

5-186
IM DLM4038-17EN
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:SIGN
Function Sets or queries whether a signed or unsigned
data format will be used (this is one of the ID and
data conditions) for CAN bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:SIGN {SIGN|UNSign}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:DATA:SIGN?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:SIGN SIGN
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:DATA:SIGN?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:DATA:SIGN SIGN
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID?
Function Queries all frame ID settings for the ID and data
conditions for FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID?
<x> = 1 to 4
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:CONDition
Function Sets or queries the frame ID data condition,
which is one of the ID and data conditions, for
FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:CONDition {BETWeen|
EQUal|GREater|LESS|NOTBetween|
NOTEqul}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:CONDition?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:FID:CONDITION BETWEEN
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:FID:CONDITION?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:FID:CONDITION BETWEEN
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:ID<y>
Function Sets or queries the frame ID value, which is one
of the ID and data conditions, for FlexRay bus
signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:ID<y> {<NRf>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:ID<y>?
<x> = 1 to 4
<y> = 1 to 2
<NRf> = 1 to 2047
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:FID:ID1 100
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:FID:ID1?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:FID:ID1 100
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:MODE
Function Sets or queries the frame ID enable/disable
condition, which is one of the ID and data
conditions, for FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:MODE {<Boolean>}
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:FID:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:FID:MODE ON
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDD
ATA:FID:MODE?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:
IDDATA:FID:MODE 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:INDIcator?
Function Queries all indicator settings for the ID and data
conditions for FlexRay bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:INDIcator?
<x> = 1 to 4
5.25 SERialbus Group