YOKOGAWA DLM4038 - Page 221

5-188
IM DLM4038-17EN
:SERialbus<x>:I2C:ANALyze?
Function Queries all I
2
C bus signal analysis settings.
Syntax
:SERialbus<x>:I2C:ANALyze?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup?
Function Queries all I
2
C bus signal analysis bus settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk?
Function Queries all I
2
C bus signal analysis clock settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk:SOURce
Function Sets or queries the clock source for I
2
C bus
signal analysis.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk:SOURce {<NRf>|MATH<y>|PODA<y>|PO
DB<y>|PODL<y>}
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk:SOURce?
<x> = 1 to 4
<NRf> = 1 to 8
<y> of MATH<y> = 1 to 4
<y> of PODA<y>, PODB<y>, PODL<y> = 0 to 7
Example
:SERIALBUS1:I2C:ANALYZE:SETUP:CLOCK:
SOURCE 1
:SERIALBUS1:I2C:ANALYZE:SETUP:CLOCK:
SOURCE?
-> :SERIALBUS1:I2C:ANALYZE:SETUP:CLO
CK:SOURCE 1
:SERialbus<x>:I2C[:ANALyze]:SETup:DA
TA?
Function Queries all I
2
C bus signal analysis data settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:DA
TA?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup:DA
TA:SOURce
Function Sets or queries the I
2
C bus signal data source.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:
DATA:SOURce {<NRf>|MATH<y>|PODA<y>|P
ODB<y>|PODL<y>}
:SERialbus<x>:I2C[:ANALyze]:SETup:
DATA:SOURce?
<x> = 1 to 4
<NRf> = 1 to 8
<y> of MATH<y> = 1 to 4
<y> of PODA<y>, PODB<y>, PODL<y> = 0 to 7
Example
:SERIALBUS1:I2C:ANALYZE:SETUP:DATA:S
OURCE 1
:SERIALBUS1:I2C:ANALYZE:SETUP:DATA:S
OURCE?
-> :SERIALBUS1:I2C:ANALYZE:SETUP:DAT
A:SOURCE 1
Description The data signal that you can specify varies
depending on the
:SERialbus<x>:I2C[:ANAL
yze]:SETup:CLOCk:SOURce
setting.
For details, see the DLM4000 User’s Manual.
:SERialbus<x>:I2C[:ANALyze]:SETup:IN
CLuderw
Function Sets or queries the on/off status of the R/W
address bit in I
2
C bus signal analysis.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:IN
CLuderw {<Boolean>}
:SERialbus<x>:I2C[:ANALyze]:SETup:IN
CLuderw?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:ANALYZE:SETUP:INCLUD
ERW ON
:SERIALBUS1:I2C:ANALYZE:SETUP:INCLUD
ERW?
-> :SERIALBUS1:I2C:ANALYZE:SETUP:INC
LUDERW 1
:SERialbus<x>:I2C:DETail?
Function Queries all I
2
C bus signal analysis result list
settings.
Syntax
:SERialbus<x>:I2C:DETail?
<x> = 1 to 4
:SERialbus<x>:I2C:DETail:DISPlay
Function Sets or queries the display mode for the I
2
C bus
signal analysis result list.
Syntax
:SERialbus<x>:I2C:DETail:DISPl
ay {FULL|LOWer|UPPer}
:SERialbus<x>:I2C:DETail:DISPlay?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:DETAIL:DISPLAY FULL
:SERIALBUS1:I2C:DETAIL:DISPLAY?
-> :SERIALBUS1:I2C:DETAIL:DISPLAY FU
LL
5.25 SERialbus Group