YOKOGAWA DLM4038 - Page 227

5-194
IM DLM4038-17EN
:SERialbus<x>:I2C:SEARch[:SETup]:MO
DE
Function Sets or queries the I
2
C bus signal search type.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:MO
DE {ADRData|EVERystart|GENeralcall|H
SMode|NONack|STARtbyte}
:SERialbus<x>:I2C:SEARch[:SETup]:MO
DE?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:MODE AD
RDATA
:SERIALBUS1:I2C:SEARCH:SETUP:MODE?
-> :SERIALBUS1:I2C:SEARCH:SETUP:
MODE ADRDATA
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack?
Function Queries all NON ACK ignore mode settings for
I
2
C bus signal searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack?
<x> = 1 to 4
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:HSMode
Function Sets or queries whether or not NON ACK will be
ignored in high-speed mode for I
2
C bus signal
searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:HSMode {<Boolean>}
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:HSMode?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:NONACK:
HSMODE ON
:SERIALBUS1:I2C:SEARCH:SETUP:NONACK:
HSMODE?
-> :SERIALBUS1:I2C:SEARCH:SETUP:NONA
CK:HSMODE 1
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:READaccess
Function Sets or queries whether or not NON ACK will be
ignored in read access mode for I
2
C bus signal
searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:READaccess {<Boolean>}
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:READaccess?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:NONACK:
READACCESS ON
:SERIALBUS1:I2C:SEARCH:SETUP:NONACK:
READACCESS?
-> :SERIALBUS1:I2C:SEARCH:SETUP:NONA
CK:READACCESS 1
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:STARtbyte
Function Sets or queries whether or not NON ACK will be
ignored in start bytes for I
2
C bus signal searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:STARtbyte {<Boolean>}
:SERialbus<x>:I2C:SEARch[:SETup]:NON
ack:STARtbyte?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:NONACK:
STARTBYTE ON
:SERIALBUS1:I2C:SEARCH:SETUP:NONACK:
STARTBYTE?
-> :SERIALBUS1:I2C:SEARCH:SETUP:NONA
CK:STARTBYTE 1
:SERialbus<x>:LIN?
Function Queries all LIN bus signal analysis and search
settings.
Syntax
:SERialbus<x>:LIN?
<x> = 1 to 4
:SERialbus<x>:LIN:ANALyze?
Function Queries all LIN bus signal analysis settings.
Syntax
:SERialbus<x>:LIN:ANALyze?
<x> = 1 to 4
:SERialbus<x>:LIN[:ANALyze]:SETup?
Function Queries all LIN bus signal analysis bus settings.
Syntax
:SERialbus<x>:LIN[:ANALyze]:SETup?
<x> = 1 to 4
:SERialbus<x>:LIN[:ANALyze]:SETup:BR
ATe
Function Sets or queries the LIN bus signal analysis bit
rate (data transfer rate).
Syntax
:SERialbus<x>:LIN[:ANALyze]:SETup:BR
ATe {<NRf>|USER,<NRf>}
:SERialbus<x>:LIN[:ANALyze]:SETup:BR
ATe?
<x> = 1 to 4
<NRf> = 1200, 2400, 4800, 9600, 19200
USER <NRf> = See the DLM4000 Features
Guide for this information.
Example
:SERIALBUS1:LIN:ANALYZE:SETUP:BRA
TE 2400
:SERIALBUS1:LIN:ANALYZE:SETUP:BRATE?
-> :SERIALBUS1:LIN:ANALYZE:SETUP:BRA
TE 2400
5.25 SERialbus Group