YOKOGAWA DLM4038 - Page 233

5-200
IM DLM4038-17EN
:SERialbus<x>:LIN:SEARch:SETup:MODE
Function Sets or queries the LIN bus signal search mode
setting.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:MO
DE {BSYNch|ERRor|IDData}
:SERialbus<x>:LIN:SEARch:SETup:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:LIN:SEARCH:SETUP:MODE BS
YNCH
:SERIALBUS1:LIN:SEARCH:SETUP:MODE?
-> :SERIALBUS1:LIN:SEARCH:SETUP:MOD
E BSYNCH
:SERialbus<x>:PSI5?
Function Queries all PSI5 signal analysis and search
settings.
Syntax
:SERialbus<x>:PSI5?
<x> = 1 to 4
:SERialbus<x>:PSI5:ANALyze?
Function Queries all PSI5 signal analysis settings.
Syntax
:SERialbus<x>:PSI5:ANALyze?
<x> = 1 to 4
:SERialbus<x>:PSI5[:ANALyze]:SETup?
Function Queries all bus setup settings for PSI5 signal
analysis.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup?
<x> = 1 to 4
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA?
Function Queries all PSI5 signal analysis data signal
settings.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA?
<x> = 1 to 4
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:BRATe
Function Sets or queries the PSI5 signal analysis bit rate
(data transfer rate).
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:BRATe {<NRf>|USER,<NRf>}
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:BRATe?
<x> = 1 to 4
<NRf> = 125000, 189000
USER <NRf> = See the DLM4000 Features
Guide for this information.
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
BRATE 125000
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
BRATE?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DA
TA:BRATE 125000
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:CTOLerance
Function Sets or queries the PSI5 signal analysis clock
tolerance.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:CTOLerance {<NRf>}
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:CTOLerance?
<NRf> = ±0.5% to ±33.3% (resolution:0.1%)
<x> = 1 to 4
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
CTOLERANCE 5
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
CTOLERANCE?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DA
TA:CTOLERANCE 5.00E+00
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:DBITs
Function Sets or queries the data length for PSI5 signal
analysis.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:DBITs {<NRf>}
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:DBITs?
<x> = 1 to 4
<NRf> = 10, 16
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
DBITS 10
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
DBITS?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DA
TA:DBITS 10
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:EDETection
Function Sets or queries the error detection method for
PSI5 signal analysis.
Syntax
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:EDETection {CRC|PARity}
:SERialbus<x>:PSI5[:ANALyze]:SETup:D
ATA:EDETection?
<x> = 1 to 4
Example
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
EDETECTION CRC
:SERIALBUS1:PSI5:ANALYZE:SETUP:DATA:
EDETECTION?
-> :SERIALBUS1:PSI5:ANALYZE:SETUP:DA
TA:EDETECTION CRC
5.25 SERialbus Group