YOKOGAWA DLM4038 - Page 260

5-227
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:SPI[:ANALyze]:SETup:CL
OCk:SOURce
Function Sets or queries the clock signal for SPI bus signal
analysis
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:CL
OCk:SOURce {<NRf>|MATH<y>|PODA<y>|PO
DB<y>|PODL<y>}
:SERialbus<x>:SPI[:ANALyze]:SETup:CL
OCk:SOURce?
<x> = 1 to 4
<NRf> = 1 to 8
<y> of MATH<y> = 1 to 4
<y> of PODA<y>, PODB<y>, PODL<y> = 0 to 7
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:CLOCK:
SOURCE 1
:SERIALBUS1:SPI:ANALYZE:SETUP:CLOCK:
SOURCE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:CLO
CK:SOURCE 1
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS?
Function Queries all chip select signal settings for SPI bus
signal analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS?
<x> = 1 to 4
:SERialbus<x>:SPI[:ANALyze]:SETup:CS
:ACTive
Function Sets or queries the chip select signal active state
for SPI bus signal analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS:ACTive {HIGH|LOW}
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS:ACTive?
<x> = 1 to 4
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:ACT
IVE HIGH
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:ACT
IVE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:CS:
ACTIVE HIGH
:SERialbus<x>:SPI[:ANALyze]:SETup:CS
:SOURce
Function Sets or queries the chip select signal for SPI bus
signal analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS:SOURce {<NRf>|MATH<y>|NONE|PODA<y
>|PODB<y>|PODL<y>}
:SERialbus<x>:SPI[:ANALyze]:SETup:
CS:SOURce?
<x> = 1 to 4
<NRf> = 1 to 8
<y> of MATH<y> = 1 to 4
<y> of PODA<y>, PODB<y>, PODL<y> = 0 to 7
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:SOU
RCE 1
:SERIALBUS1:SPI:ANALYZE:SETUP:CS:SOU
RCE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:CS:
SOURCE 1
Description The chip select signal that you can specify varies
depending on the
:SERialbus<x>:SPI[:ANAL
yze]:SETup:CLOCk:SOURce
setting.
For details, see the DLM4000 User’s Manual.
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>?
Function Queries all data signal settings for SPI bus signal
analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>?
<x> = 1 to 4
<y> = 1 to 2
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>:SOURce
Function Sets or queries the data signal for SPI bus signal
analysis.
Syntax
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>:SOURce {<NRf>|MATH<z>|PODA<z>|
PODB<z>|PODL<z>}
:SERialbus<x>:SPI[:ANALyze]:SETup:DA
TA<y>:SOURce?
<x> = 1 to 4
<y> = 1 to 2
<NRf> = 1 to 8
<z> of MATH<z> = 1 to 4
<z> of PODA<z>, PODB<z>, PODL<z> = 0 to 7
Example
:SERIALBUS1:SPI:ANALYZE:SETUP:DATA1:
SOURCE 1
:SERIALBUS1:SPI:ANALYZE:SETUP:DATA1:
SOURCE?
-> :SERIALBUS1:SPI:ANALYZE:SETUP:DAT
A1:SOURCE 1
Description The data signal that you can specify varies
depending on the
:SERialbus<x>SPI[:ANALy
ze]:SETup:CLOCk:SOURce
setting.
For details, see the DLM4000 User’s Manual.
5.25 SERialbus Group