YOKOGAWA DLM4038 User Manual

5-247
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:TRIGger:ACTion:MAIL?
Function Queries all of the settings for email notification
that is sent when trigger conditions are met.
Syntax
:TRIGger:ACTion:MAIL?
:TRIGger:ACTion:MAIL:COUNt
Function Sets or queries the upper limit of email
notifications that are sent when trigger conditions
are met.
Syntax
:TRIGger:ACTion:MAIL:COUNt {<NRf>}
:TRIGger:ACTion:MAIL:COUNt?
<NRf> = 1 to 1000
Example
:TRIGGER:ACTION:MAIL:COUNT 1
:TRIGGER:ACTION:MAIL:COUNT?
-> :TRIGGER:ACTION:MAIL:COUNT 1
:TRIGger:ACTion:MAIL:MODE
Function Sets or queries whether or not the DLM4000 will
send email notification as an action.
Syntax
:TRIGger:ACTion:MAIL:
MODE {<Boolean>}
:TRIGger:ACTion:MAIL:MODE?
Example
:TRIGGER:ACTION:MAIL:MODE ON
:TRIGGER:ACTION:MAIL:MODE?
-> :TRIGGER:ACTION:MAIL:MODE 1
:TRIGger:ACTion:SAVE
Function Sets or queries whether or not the DLM4000 will
save waveform data to the storage medium as an
action when trigger conditions are met (on/off).
Syntax
:TRIGger:ACTion:SAVE {<Boolean>}
:TRIGger:ACTion:SAVE?
Example
:TRIGGER:ACTION:SAVE ON
:TRIGGER:ACTION:SAVE?
-> :TRIGGER:ACTION:SAVE 1
:TRIGger:ACTion:STARt
Function Starts the action-on-trigger operation.
Syntax
:TRIGger:ACTion:STARt
Example
:TRIGGER:ACTION:START
Description Use
:TRIGger:ACTION:STOP
to stop trigger
actions.
:TRIGger:ACTion:STOP
Function Stops the action-on-trigger operation.
Syntax
:TRIGger:ACTion:STOP
Example
:TRIGGER:ACTION:STOP
Description This command only stops trigger actions and
does not cancel the setting. Use
:TRIGger:
ACTION:STARt
to resume trigger actions.
:TRIGger:ADB?
Function Queries all A Delay B trigger settings.
Syntax
:TRIGger:ADB?
:TRIGger:ADB:DELay
Function Sets or queries the for condition B for the A
Delay B trigger.
Syntax
:TRIGger:ADB:DELay {<Time>}
:TRIGger:ADB:DELay?
<Time> = 10 ns to 10 s (2-ns steps)
Example
:TRIGGER:ADB:DELAY 10ns
:TRIGGER:ADB:DELAY?
-> :TRIGGER:ADB:DELAY 10ns
:TRIGger:{ATRigger|BTRigger}?
Function Queries all trigger condition settings.
Syntax
:TRIGger:{ATRigger|BTRigger}?
:TRIGger{[:ATRigger]|:BTRigger}:CAN?
Function Queries all CAN bus signal trigger settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN?
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
BRATe
Function Sets or queries the CAN bus signal trigger bit rate
(data transfer rate).
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
BRATe {<NRf>|USER,<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
BRATe?
<NRf> = 33300, 83300, 125000, 250000,
500000, 1000000
USER <NRf> = See the DLM4000 Feature Guide
for this information.
Example
:TRIGGER:ATRIGGER:CAN:BRATE 83300
:TRIGGER:ATRIGGER:CAN:BRATE?
-> :TRIGGER:ATRIGGER:CAN:BRATE 83300
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
EFRame?
Function Queries all CAN bus signal trigger error settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
EFRame?
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
EFRame:CRC
Function Sets or queries the CAN bus signal trigger CRC
error setting.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
EFRame:CRC {<Boolean>}
:TRIGger{[:ATRigger]|:BTRigger}:CAN:
EFRame:CRC?
Example
:TRIGGER:ATRIGGER:CAN:EFRAME:CRC ON
:TRIGGER:ATRIGGER:CAN:EFRAME:CRC?
-> :TRIGGER:ATRIGGER:CAN:EFRAME:C
RC 1
5.34 TRIGger Group

YOKOGAWA DLM4038 Specifications

General

Brand	YOKOGAWA
Model	DLM4038
Category	Test Equipment
Language	English