YOKOGAWA DLM4038 - Page 312

5-279
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:ID<x>:PATTern
Function Sets or queries the ID pattern, which is one of the
IDOR conditions, for LIN bus signal triggering in
binary notation.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:ID<x>:PATTern {<Stri
ng>}
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:ID<x>:PATTern?
<x> = 1 to 4
Example
:TRIGGER:ATRIGGER:LIN:IDOR:IDENTIFIE
R:ID1:PATTERN "101100"
:TRIGGER:ATRIGGER:LIN:IDOR:IDENTIFIE
R:ID1:PATTERN?
-> :TRIGGER:ATRIGGER:LIN:IDOR:IDENTI
FIER:ID1:PATTERN "101100"
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:MODE
Function Sets or queries the ID enable/disable condition
for LIN bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:MODE {<Boolean>}
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:MODE?
Example
:TRIGGER:ATRIGGER:LIN:IDOR:IDENTIFIE
R:MODE ON
:TRIGGER:ATRIGGER:LIN:IDOR:IDENTIFIE
R:MODE?
-> :TRIGGER:ATRIGGER:LIN:IDOR:IDENTI
FIER:MODE 1
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:PFORmat
Function Sets or queries the ID input format, which is
one of the IDOR conditions, for LIN bus signal
triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:PFORmat {BINary|
HEXa}
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
IDOR:IDENtifier:PFORmat?
Example
:TRIGGER:ATRIGGER:LIN:IDOR:IDENTIFIE
R:PFORMAT BINARY
:TRIGGER:ATRIGGER:LIN:IDOR:IDENTIFIE
R:PFORMAT?
-> :TRIGGER:ATRIGGER:LIN:IDOR:IDENTI
FIER:PFORMAT BINARY
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
MODE
Function Sets or queries the LIN bus signal trigger mode
setting.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
MODE {BSYNch|ERRor|IDData|IDOR}
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
MODE?
Example
:TRIGGER:ATRIGGER:LIN:MODE BSYNCH
:TRIGGER:ATRIGGER:LIN:MODE?
-> :TRIGGER:ATRIGGER:LIN:MODE BSYNCH
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
SOURce
Function Sets or queries the LIN bus signal trigger source
signal.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
SOURce {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
SOURce?
<NRf> = 1 to 8
Example
:TRIGGER:ATRIGGER:LIN:SOURCE 1
:TRIGGER:ATRIGGER:LIN:SOURCE?
-> :TRIGGER:ATRIGGER:LIN:SOURCE 1
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
SPOint
Function Sets or queries the LIN bus signal trigger sample
point.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
SPOint {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:LIN:
SPOint?
<NRf> = 18.8 to 90.6
Example
:TRIGGER:ATRIGGER:LIN:SPOINT 18.8
:TRIGGER:ATRIGGER:LIN:SPOINT?
-> :TRIGGER:ATRIGGER:LIN:SPOINT 18.8
:TRIGger{[:ATRigger]|:BTRigger}:PATT
ern?
Function Queries all state trigger settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:PATT
ern?
5.34 TRIGger Group