YOKOGAWA DLM4038 - Page 332

5-299
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:TRIGger{[:ATRigger]|:BTRigger}:SPI:
DATA<x>:SOURce
Function Sets or queries the data signal for SPI bus signal
triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SPI:
DATA<x>:SOURce {<NRf>|PODA<y>|
PODB<y>|PODL<y>}
:TRIGger{[:ATRigger]|:BTRigger}:SPI:
DATA<x>:SOURce?
<x> = 1 to 2
<NRf> = 1 to 8
<y> of PODA<y>, PODB<y>, PODL<y> = 0 to 7
Example
:TRIGGER:ATRIGGER:SPI:DATA1:SOURCE 1
:TRIGGER:ATRIGGER:SPI:DATA1:SOURCE?
-> :TRIGGER:ATRIGGER:SPI:DATA1:SOUR
CE 1
Description The data signal that you can specify varies
depending on the “
:TRIGger{[:ATRigger]|:
BTRigger}:SPI:CLOCk:SOURce
” setting.
For details, see the DLM4000 User’s Manual.
:TRIGger{[:ATRigger]|:BTRigger}:SPI:
MODE
Function Sets or queries the wiring system (three-wire or
four-wire) for SPI bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SPI:
MODE {WIRE3|WIRE4}
:TRIGger{[:ATRigger]|:BTRigger}:SPI:
MODE?
Example
:TRIGGER:ATRIGGER:SPI:MODE WIRE3
:TRIGGER:ATRIGGER:SPI:MODE?
-> :TRIGGER:ATRIGGER:SPI:MODE WIRE3
:TRIGger{[:ATRigger]|:BTRigger}:TYPE
Function Sets or queries the trigger type.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:TY
PE {PATTern|WIDTh|OR|TV|SIMPle|PULSe
|QUALify|CANBus|CANFDbus|FLEXray|I2C
Bus|LINBus|PSI5|SENT|SPATtern|SPIBus
|UART}
:TRIGger{[:ATRigger]|:BTRigger}:TY
PE?
Example
:TRIGGER:ATRIGGER:TYPE SIMPLE
:TRIGGER:ATRIGGER:TYPE?
-> :TRIGGER:ATRIGGER:TYPE SIMPLE
Description The settings that are available for
:TRIGger:BTRigger:TYPE
are
{PATTern|SI
MPle|QUALify|CANBus|CANFDbus|FLEXray
|I2CBus|LINBus|SENT|SPATtern|SPIBus|
UART}
.
:TRIGger{[:ATRigger]|:BTRigger}:UA
RT?
Function Queries all UART signal trigger settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}UART?
:TRIGger{[:ATRigger]|:BTRigger}:UART
:BITorder
Function Sets or queries the UART signal trigger bit order.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:
UART:BITorder {LSBFirst|MSBFirst}
:TRIGger{[:ATRigger]|:BTRigger}:
UART:BITorder?
Example
:TRIGGER:ATRIGGER:UART:BITORDER LSBF
IRST
:TRIGGER:ATRIGGER:UART:BITORDER?
-> :TRIGGER:ATRIGGER:UART:BITORDER L
SBFIRST
:TRIGger{[:ATRigger]|:BTRigger}:UART
:BRATe
Function Sets or queries the UART signal trigger bit rate
(data transfer rate).
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:
UART:BRATe {<NRf>|USER,<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:
UART:BRATe?
<NRf> = 1200, 2400, 4800, 9600, 19200
USER <NRf> = See the DLM4000 Feature Guide
for this information
Example
:TRIGGER:ATRIGGER:UART:BRATE 2400
:TRIGGER:ATRIGGER:UART:BRATE?
-> :TRIGGER:ATRIGGER:UART:BRATE 2400
:TRIGger{[:ATRigger]|:BTRigger}:UART
:DATA?
Function Queries all UART signal trigger data settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:
UART:DATA?
:TRIGger{[:ATRigger]|:BTRigger}:UART
:DATA:ASCii
Function Sets the UART bus signal trigger data in ASCII
format.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:
UART:DATA:ASCii {<String>}
Example
:TRIGGER:ATRIGGER:UART:DATA:ASCII "T
EST"
5.34 TRIGger Group