YOKOGAWA WT1803

Index-3
IM WT1801-01EN
Index
linear scale .................................................................... 4-3, 5-2
linear scale, motor evaluation ............................................... 4-3
linear scaling, auxiliary input................................................. 5-2
line filter ................................................................ 2-19, 4-4, 5-3
line filter, auxiliary input ........................................................ 5-3
line filter, motor evaluation .................................................... 4-4
linkage ................................................................................ 15-2
Load Bmp ........................................................................... 7-10
load items ........................................................................... 7-10
load setup ........................................................................... 18-5
local ........................................................................... 22-4, 23-3
lower scale........................................................................... 11-3
M
Page
manual CSV conversion ............................................ 16-9, 17-5
manual integration mode ...................................................... 9-7
manual storage mode ......................................................... 17-2
master................................................................................. 8-10
matrix .................................................................................... 7-1
matrix display........................................................................ 7-1
max hold ............................................................................... 8-5
maximum capturing count .................................................. 16-4
maximum harmonic to be measured .................................... 3-2
maximum storage count ..................................................... 17-2
max order ............................................................................. 3-2
measured harmonic order .................................................... 3-2
measurement function .......................................................... 1-6
measurement period........................................................... 2-18
menu font size .................................................................... 22-7
menu language ................................................................... 22-6
message language ............................................................. 22-6
minimum harmonic to be measured ..................................... 3-2
min order .............................................................................. 3-2
mode..................................................................................... 9-7
motor .................................................................................... 4-1
motor efficiency .................................................................... 4-9
motor poles ........................................................................... 4-7
moving average .................................................................. 2-21
N
Page
name..................................................................................... 8-1
net drive .............................................................................. 21-4
network ...................................................................... 21-1, 22-4
network drive ............................................................. 18-1, 21-4
normal integration mode ....................................................... 9-8
normal mode (Trg) .............................................................. 10-1
NULL ......................................................................... 23-1, 23-3
NULL SET........................................................................... 23-1
NULL values ....................................................................... 23-2
NULL status ........................................................................ 23-2
numbering........................................................................... 18-4
number of displayed items......................................... 17-4, 18-3
numeric data display............................................................. 7-1
numeric data display, turning on and off ............................. 13-2
O
Page
offset value, auxiliary input ................................................... 5-2
offset value, motor evaluation ............................................... 4-3
optimization ............................................................... 16-4, 17-2
optimize count ........................................................... 16-4, 17-2
order ..................................................................................... 1-4
other displays ...................................................................... 11-1
OTHERS .............................................................................. 11-1
overview ............................................................................. 22-2
P
Page
p-p compression ................................................................. 10-3
PAGE DOWN ....................................................................... 7-3
PAGE END ........................................................................... 7-3
PAGE TOP ............................................................................ 7-3
PAGE UP .............................................................................. 7-3
paper feeding...................................................................... 20-3
Pc formula ............................................................................ 8-9
peak over-range jump......................................................... 2-16
peak over status ................................................................ 16-11
phase .................................................................................. 8-10
phase difference ................................................................. 8-10
PLL source ........................................................................... 3-1
pole ....................................................................................... 4-7
power coefficient ................................................................. 2-15
power range........................................................................ 2-12
preference .......................................................................... 22-7
preset items .......................................................................... 7-6
PRINT ................................................................................. 20-6
Print At Start ....................................................................... 20-3
print conditions ................................................................... 20-1
print count ........................................................................... 20-2
printing ................................................................................ 20-1
printing, execution of .......................................................... 20-6
print interval ........................................................................ 20-2
PRINT MENU ..................................................................... 20-1
print modes ......................................................................... 20-2
pulse input range .................................................................. 4-5
pulse N ................................................................................. 4-7
pulse range lower ................................................................. 4-5
pulse range upper................................................................. 4-5
pulse rating ........................................................................... 4-5
pulses ................................................................................... 4-7
Q
Page
q mode................................................................................. 9-11
R
Page
RAM-0 ................................................................................ 18-1
range, auxiliary input ............................................................ 5-1
range, motor evaluation ........................................................ 4-3
raster .................................................................................. 10-3
Rated Freq Lower ................................................................. 4-6
Rated Freq Upper ................................................................. 4-6
Rated Lower ......................................................................... 4-5
rated time of integrated D/A output ..................................... 9-12
Rated Upper ......................................................................... 4-5
real-time continuous integration mode ................................. 9-9
real-time Control ................................................................. 9-10
real-time normal integration mode ........................................ 9-9
real-time print mode............................................................ 20-2
real-time storage mode....................................................... 17-2
real time control ......................................................... 17-3, 20-3
record to file ........................................................................ 16-7
remote control..................................................................... 22-3
remote mode, clearing ............................................... 22-4, 23-3
Reset Pattern........................................................................ 7-6
Resolution........................................................................... 22-7
rising ................................................................................... 10-5
S
Page
S,Q Formula ......................................................................... 8-8
S/Q/λ/Φ ................................................................................. 7-5
sampling frequency .............................................................. 8-9
save conditions ................................................................... 16-8