Zte ZXV10 W615 User Manual

89 pages

To Next Page

To Previous Page

ZXV10 W615 User Manual

60 Confidential and Proprietary Information of ZTE CORPORATION

3. Click Submit.

—END OF STEPS—

Setting a Classification Rule

This section describes how to set a classification rule.

Steps

1. Select Application > QoS > Classification. The following page is

displayed.

2. Configure the parameters. Refer to the following table.

Parameter Description

User Manual1
Product Introduction3
Product Overview3
Typical Application3
Interface and Button Description4
Technical Specifications4
Physical Specification4
Electric Parameters4
Environment Requirement5
IP Protection Class5
Passed Certifications5
Antenna Requirement5
Configuration Preparation6
Login6
Introduction to the GUI for Software Setup7
Software Interface7
Device Status9
Checking Device Information9
Device Information9
Checking Information of Network Interfaces10
Checking Ethernet Interface Information10
Ethernet Interface Information10
Checking WAN Connection10
WAN Connection Information11
Checking WLAN Interface Information11
WLAN Interface Information12
Network Configuration13
Broadband Connection Configuration13
Configuring a Broadband Connection (Fit AP)13
Configuring a Broadband Connection (Fat AP)15
WLAN Configuration16
Setting Basic Information16
Setting SSID20
Setting Security Information22
Non-Encryption23
WPA-PSK Encryption23
WPA-EAP Encryption23
WEP Encryption25
WAPI-PSK Encryption26
WAPI-CERT Encryption26
WEP-EAP Encryption27
Setting Rate Limit29
Setting Access Control List30
Checking Associated Devices31
Scanning an AP32
Setting WDS33
Setting STA WMM36
Setting AP WMM38
Setting Automatic Channel Switching39
Setting Wireless Mode40
Setting the Network Configuration41
Addresses Management43
Managing Addresses43
Setting DHCP Conditional Serving Pool44
Managing an Ipv6 Address45
Routing Management46
Setting an Ipv4 Static Route46
Setting an Ipv6 Static Route47
Setting a Dynamic Route48
Security Configuration50
Setting a Firewall50
Setting IP Filter (Fat AP)51
Setting MAC Filter53
Checking the Service List55
Setting Service Control (Fat AP)55
Setting the ALG Switch (Fat AP)57
Application Configuration58
Configuring Upnp (Fat AP)58
Setting a Device Name (Fat AP)59
Qos Configuration60
Configuring Basic Qos Parameters61
Setting a Classification Rule62
Configuring Congestion Management64
Configuring SNTP65
IGMP Configuration66
Configuring WAN Connection (Fat AP)67
Configuring IGMP Snooping67
Configuring MLD Snooping68
Configuring LED Control69
Management Configuration70
Managing Snmpv1/V2C70
Snmpv3 Security Management (USM)71
Managing Snmpv3 Users71
Managing Snmpv1/V2C Users72
Snmpv3 Access Control Management (VACM)73
Managing Context73
Managing Security Groups73
Managing View Subtree74
Managing the Access Table75
User Management77
Managing Users77
Managing Automatic Logout78
Device Management78
Configuring System Management78
Setting Version Upgrade79
Managing User Configuration80
Managing the Default Configuration81
Configuring Log Management82
Access Point Management84
Setting the AP Mode84
Setting an AP Name84
Diagnosis Configuration85
Performing Ping Diagnosis85
Configuring Trace Route Diagnosis86
FCC Regulations88
RF Exposure Information88
Glossary89

Questions and Answers:

Need help?

Do you have a question about the Zte ZXV10 W615 and is the answer not in the manual?

Zte ZXV10 W615 Specifications

General

Wireless Standards	802.11b/g/n
Frequency Band	2.4 GHz
Security	WEP, WPA, WPA2
Antenna	External
Humidity	5% to 95% (non-condensing)

Related product manuals

Zte ZXV10 W811N

57 pages

Zte ZXV10 W615 User Manual

Table of Contents

Questions and Answers:

Zte ZXV10 W615 Specifications

Related product manuals