Agilent Technologies 81104A - Page 85

130 pages

To Next Page

To Previous Page

Using the 81110A/81104A

The

he he

he L

s s

s S

Because output 2 is no longer used, its impedance parameters are no

longer available, see figure below.

The Levels graphic page is also modified to indicate the multiple levels

formed by outputs 1 and 2:

Main Page

Notice4
About this Book6
- Output Modules for 81104A Mainframe6
- Output Modules for 81110A Mainframe6
  - Conventions Used in this Book7
Safety Information8
- Safety8
- Warning8
- Safety Symbols9
Introducing the 81110A/81104A Pulse and Pattern Generators15
What you can do with the 81110A/81104A16
- Basic Features16
- Benchtop Testing16
- Automated Testing17
- Upgrade Capability17
The Front Panel18
Operating the 81110A/81104A20
- Switching On the Instrument20
- The Basic Screens21
- Adjusting Parameters24
  - Standard Procedure24
  - Advanced Procedures26
- Switching the Outputs On and Off27
- Using the Special Function Keys28
Help is Available29
The Rear Panel30
Getting Started31
Setting Up a Clock Signal32
Setting Up a Pulse Signal37
Setting Up a Serial Data Stream Signal41
Setting Up an Edge-Displacement Signal45
Setting Up a Dual Clock Signals50
Setting Up a Burst Signal55
Using the 81110A/81104A59
The Mode/Trigger Screen60
- Overview60
  - Pulse Types61
  - Pattern Formats62
- Continuous Pulses Mode63
- Continuous Burst Mode64
- Continuous Pattern Mode65
- Triggered Pulses Mode66
- Triggered Burst Mode68
- Triggered Pattern Mode70
- Gated Pulses Mode72
- Gated Burst Mode74
- Gated Pattern Mode75
- External Width Mode76
The Timing Screen77
- Pulse-Period Parameter79
- Pulse Delay Parameter79
- Pulse Width Parameter80
- Pulse Trailing-Delay Parameter81
- Pulse Leading-Edge Parameter81
- Pulse Trailing Edge Parameter82
The Levels Screen83
- Normal/Complement Parameter84
- Separate/Added Outputs Parameter84
- Offset/Amplitude, High/Low Level Parameters86
- Voltage/Current Mode (mV/V/mA/A)86
- Output Source Impedance Parameter (50 W into)87
- Load Impedance Parameter (50.0W)87
- Output Voltage and Power Protection87
The Pattern Screen88
- Update Parameter89
- Address Parameter89
- Last Parameter89
- Bit-Editing Window90
- RZ/NRZ Data Format90
- Outputs (CH1,CH2) and Strobe Out (STRB)90
- Block Editing Functions (CH1/CH2/BOTH/STRB)91
- Hints on Editing Pattern Data94
  - Example94
The Limits Screen95
The Trigger-Level Screen96
- EXT-IN Parameter96
- EXT-IN Impedance Parameter (50W/10kW)97
- CLK-IN Parameter97
- CLK-IN Impedance Parameter (50W/10kW)97
- TRIGGER-OUT Level Parameter97
- STROBE-OUT Level Parameter97
The Memory Card Screen98
- Current Directory Parameter (Dir Path)99
- Filename Parameter100
- Memory Card Operations100
The Configuration Screen103
- GP-IB Address103
- Perform Operation “Selftest”103
- Perform Operation “Calibrate”104
- Parameter Grouping (Group Params by)104
- Pulse Period Source105
- PLL Reference105
- Deskew Parameter105
The Output Screens106
Warnings and Errors107
- Warning and Error Reporting Example108
Installation & Maintenance111
Initial Inspection112
- Standard Deliverables113
- Options and Accessories:114
Power Requirements116
- Replacing the Fuse117
Power Cable118
Ventilation Requirements119
- Thermal Protection119
  - Overheating Detection119
  - Fan Failure119
Battery120
- Battery Replacement121
Operating Environment122
Cleaning Recommendation123
Acoustic Noise Emission124
- Acoustic Noise Emission124
- Geräuschemissionswerte124

Agilent Technologies 81104A - Page 85

Table of Contents

Related product manuals