EasyManua.ls Logo

Alde Compact 3010 - Mounting the Wall Flue; Mounting the Inlet;Exhaust Hose; Mounting the Expansion Tank

Alde Compact 3010
54 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
19
US/CAN
Window
Prohibited zone
NOTICE
The ue shall be mounted with the bend upwards,
(the wall ue is also marked TOP/OBEN).
CAUTION
OBSERVERA
ATTENTION
VOORZICHTIG
Check the hose run to ensure that water cannot be
retained in the inlet/exhaust hose.
Figure B
7
8
10b
9
11
13
12a
14
15
16
10a
12b
DANGER
FARA
DANGER
GEFAHR
FARE
VAARA
PELIGRO
PERICOLO
GEVAAR
CARBON MONOXIDE POISONING
Thisboilercanproducedangerouscarbonmonoxide
(CO)gasifitisnotinstalledandusedproperly.
MOUNTING THE WALL FLUE
Theboilermayonlybemountedwiththeoriginalue.
Theuemustnotbeblocked.Thewallueshouldbe
mountedonasurfaceasataspossible,allowingair
tofreelycirculatepasttheue.Theueshouldnotbe
mountedcloserthan12inches(300mm)sidewayson
fromanopeningwindoworventilationinlet.Theuemust
notbemountedunderawindowthatcanbeopened,ora
ventilationinlet(Sedrawingbelow).
If the ue is mounted closer than the measurements
given above, a window circuit- breaker shall be
installed that shuts off the LP Gas supply when the
window is open. Toguaranteethefunctionoftheboiler,
noobjectshouldbettedwithinaradiusof12inches
(300mm)aroundthechimney(noofcialclaim).The
distancefromtheuetotheventilationinletunderthe
vehiclemustbeatleast12inches(300mm)(notalegal
requirement).Thedistancefromuetorellingpositionor
ventilationforfuelshallbeatleast20in/500mm.
Marktheplacewheretheueistobelocated.Thendrill
aØ3.25inch(83mm)holethroughtheouterwall.First
mountthegasket(B7)andthenscrewdowntheue(B
8)withthe6platescrews(B9).Ifthesurfaceisstruc-
tured,ofball-hammeredplatetype,sealingcompound
forautomobileapplicationmustbeusedwiththegasket.
Mounttheplasticcap(B10a)andtheOring(B10b)with
thetwoscrewsprovided(B11).
MOUNTING THE INLET/EXHAUST
HOSE
Hoselengthwithwallue:min.1.5feet(0.5m)andmax.
6.5feet(2.0m).Measureandcuttherequiredlengthof
inlethose(Ø3in/75mm).Theexhausthose(Ø2in/50
mm)shouldbecutoffsoitbecomesapproximately2
inches(50mm)longerthanthesuctionhose.Thisapplies
tohoselengthsover3feet(1m).Notethatthehoseswill
goontothehosesleeves0.75inches(20mm).Pushthe
exhausthoseintotheinlethose.Firstmounttheexhaust
hose(B12a).Adda1/8inch(3mm)stringofHighTem-
perature(min500°F)Siliconpaste(B12b)ontheinside
ofthe2-inch(50mm)hose.(e.g.,DowCorningq3-1566).
Puttheexhausthoseoverthewallueconnection(B8).
Tightenthe40-60hoseclamp(B13).Puttheairinlettube
(B14)onthewallueconnection.Tightenthe60-80hose
clamp(B15).Usethesameprocedurewhenconnecting
thehosestotheboiler.Staplethehose(B16)onc/c2
feet(600mm)orequivalent.
MOUNTING THE EXPANSION TANK
Mounttheexpansiontankatleast7.5inches(200mm)
higherthanthehighestpointoftheheatingsystemor
boiler.Iftheexpansiontankismountedinawardrobefor
example,Alde’sprotectivehousingshouldbemounted
aroundtheexpansiontank.Thiswillstopaccidental
splashescomingincontactwithclothing.Leaveaspace
ofatleast8inches(220mm)abovetheexpansiontank
fortoppingupandservice.Fittheexpansionvessel
usingthescrewsandsupportrings(C16)supplied.Ifa
circulatingpumpisttedintheexpansionvessel,itisa
suckingpumpandincominghosesshallthereforealways
beconnectedtothepipeunderneaththepumpandout-
goinghosestothepipealongside(seeg.C).Theair
venthose(C17)mustbeassembledverticallyupwards
andclampeddownsothatcreasescannotforminthe
hose.Thedrainagehose(C18)mustbemountedsothat
itgoestheshortestroutefromtheexpansiontankout
throughtheoorofthevehicle.Cutthehoseobliquelyat
a30ºanglefromthedirectionoftravelunderthevehicle.
Aftertheheatingsystemhasbeenlled,thetankshallbe
sealedwiththecap.
Figure C
18
16
17
min8inches

Table of Contents

Other manuals for Alde Compact 3010

Related product manuals