EasyManuals Logo

Allen-Bradley MicroLogix 1100 Instruction Set Reference Manual

Allen-Bradley MicroLogix 1100
616 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #496 background imageLoading...
Page #496 background image
Publication 1763-RM001C-EN-P - October 2009
496 Fault Messages and Error Codes
003F COP/CPW/FLL
OUTSIDE OF DATA
FILE SPACE
A COP, CPW or FLL instruction length
parameter references outside of the
entire data space.
Recoverable Correct the program to ensure that the
length and parameter do not point outside
of the data file space.
Re-compile, reload the program and enter
the Run mode.
0042 INVALID RECIPE
NUMBER
Number of Recipes specified is
greater than 256.
Recoverable Correct the value for Number of Recipes.
Re-compile, reload the program and enter
the Run mode.
0044 INVALID WRITE TO
RTC FUNCTION FILE
Write attempt to RTC function file
failed. This only occurs when
attempting to write invalid data to
the RTC function file. Examples of
invalid data are: setting the Day of
Week to zero, or setting the Date to
February 30th.
Recoverable Correct the invalid data.
Re-compile, reload the program and enter
the Run mode.
0050 CONTROLLER TYPE
MISMATCH
A particular controller type was
selected in the user program
configuration, but did not match the
actual controller type.
Non-User Connect to the hardware that is specified in
the user program, or
Reconfigure the program to match the
attached hardware.
0051 BASE TYPE
MISMATCH
A particular hardware type (AWA,
BWA, BBB) was selected in the user
program configuration, but did no
match the actual base.
Non-User Connect to the hardware that is specified in
the user program, or
Reconfigure the program to match the
attached hardware.
0052 MINIMUM SERIES
ERROR
The hardware minimum series
selected in the user program
configuration was greater than the
series on the actual hardware.
Non-User Connect to the hardware that is specified in
the user program, or
Reconfigure the program to match the
attached hardware.
xx71
(1)
EXPANSION I/O
HARDWARE ERROR
The controller cannot communicate
with an expansion I/O module.
Non-Recoverable Check connections.
Check for a noise problem and be sure
proper grounding practices are used.
Replace the module.
Cycle power.
xx79
(1)
EXPANSION I/O
MODULE ERROR
An expansion I/O module generated
an error.
Non-Recoverable Refer to the I/O Module Status (IOS) file.
Consult the documentation for your specific
I/O module to determine possible causes of
a module error.
xx81
(1)
EXPANSION I/O
HARDWARE ERROR
The controller cannot communicate
with an expansion I/O module.
Non-User Check connections.
Check for a noise problem and be sure
proper grounding practices are used.
Replace the module.
Cycle power.
0083 MAX I/O CABLES
EXCEEDED
The maximum number of expansion
I/O cables allowed was exceeded.
Non-User Reconfigure the expansion I/O system so
that it has an allowable number of cables.
Cycle power.
Error
Code
(Hex)
Advisory Message Description Fault
Classification
Recommended Action
efesotomasyon.com - Allen Bradley,Rockwell,plc,servo,drive

Table of Contents

Other manuals for Allen-Bradley MicroLogix 1100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Allen-Bradley MicroLogix 1100 and is the answer not in the manual?

Allen-Bradley MicroLogix 1100 Specifications

General IconGeneral
Processor32-bit
Programming SoftwareRSLogix 500
MountingDIN rail or panel mount
Power Supply24V DC
TypeCompact PLC
Digital Inputs12
Digital Outputs8
Analog Inputs4 (depending on model)
Analog OutputsOptional with expansion module
Programming LanguageLadder Logic
Operating Temperature0 to 55 °C (32 to 131 °F)
SeriesMicroLogix

Related product manuals