Home
Ametek
Laboratory Equipment
ta7000R
Ametek ta7000R User Manual
4
of 1
of 1 rating
57 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
PN T900-013, Rev A
Connecting Span Gas
The ta7000R Monitor uses Span gas for calibr
ation purposes.
The instrument
connection is made at the
“
AUX”
1/16-inch VICI port on the ta7000R Rear Panel.
Pr
essurize this external line to 80 PSIG (minimum 80 PSIG, maximum 90 PSIG).
Making the Vent Connections
All vent ports must be connected to a vent that is connected to a saf
e area.
The
vent should be at atmospheric pr
essure.
2-12 | ta7000R Gas Purity Monitor
29
31
Table of Contents
Table of Contents
3
Safety Notes
5
Grounding
5
Personnel and Equipment Safety Information
6
General Safety Considerations
9
Components and Functions
9
Mercury Vapor
9
UV Light
9
Electrical Hazard
9
Electromagnetic Compatibility (EMC)
10
Warning Labels
11
Overview
13
Introduction to the Ta7000R Gas Purity Monitor
13
Functional Overview of the Ta7000R Gas Purity Monitor
14
Ta7000R Gas Purity Monitor Front Panel
17
Installation and Start-Up
19
Safety Considerations
19
Pre-Installation Requirements
21
Personnel Technical Level Required for Installation
21
Storage Prior to Installation
21
Unpacking and Inspecting the Equipment
21
Ta7000R Monitor Location Requirements
22
Electrical Preparations and Connections
23
Support Gas Utilities Preparations
23
General Notes on Regulators and Plumbing
24
Tools, Equipment, Hardware, and Supplies Required for Installation
25
Installing the Mechanical Components
26
Making Gas Connections
29
Connecting the Sample and Carrier Gas
29
Connecting Actuator Gas
29
Connecting Span Gas
30
Making the Vent Connections
30
Making the Electrical Connections
31
Connecting AC Power
31
Connecting Peripheral Equipment
31
Connecting Communications Cables
31
Connecting to a Printer
32
Powering up the Ta7000R Gas Purity Monitor
33
Starting the Ta7000R in the Warm-Up Cycle
34
Working from the Run Mode Screen
35
Initiating a Blank Run
36
User Interface
37
Introduction to the User Interface
37
Working from the User Interface
38
Operator State Diagram (Menu Map)
39
Working from the Main Menu
40
Working from the Page Screens
41
Working from the System Settings Screen
42
Setting the Clock
42
Printing Chromatograms
42
Enabling Enhanced Detection Limit (EDL) Analysis Mode
42
Printing Diagnostic Information
42
Viewing System Information on the Temperatures & Status Screen
43
Working from the Calibration Screen
44
Setting Auto-Calibration Parameters
45
Initiating a Manual Calibration
46
Saving Changes to Non-Volatile RAM
47
Powering down the Ta7000R Gas Purity Monitor
48
Troubleshooting
49
Error Messages
49
Detector Controller Error
49
Temperature out of Range
50
Carrier Pressure out of Range
50
Analog Signal Zeroing Error
50
Calib Pressure out of Range
50
Event Program Error
51
Printer Error
51
Database Change, Update NV RAM
51
Specifications
53
Model Designation and Detection Limit Specifications
53
Ta7000R Standard Model
53
Performance Specifications
53
Sample/Carrier Gas Supplies
54
Gas Ports
54
Actuator Gas
54
Calibration Gas
54
Chassis
55
Outputs
55
Ta7000R PLC Output Format
55
Communication Ports
56
Parallel Printer Port (LPT1)
56
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Ametek ta7000R and is the answer not in the manual?
Ask a question
Ametek ta7000R Specifications
General
Brand
Ametek
Model
ta7000R
Category
Laboratory Equipment
Language
English
Related product manuals
Ametek PARSTAT 4000
35 pages
Ametek Reichert XCEL 255
24 pages
Ametek VersaSTAT LC Series
35 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
