L0118G
8-4
Cleaning Fixed Bottom Screen
1. Open the door to the vendor to stop the chiller.
2. A vacuum attachment with a brush is preferred:
however, a bristle brush may also be used.
3. Do not use water or other liquid chemicals or
solvents.
4. From the underside of the vendor gently sweep
lint away from the screen with the brush. Do not
push the lint into the screen.
5. Clean the floor under the vendor with the brush,
removing any obstructions such as cardboard
and wrappers.
6. Close the vendor door.
Cleaning Removable Bottom Screen
1. Open the door to the vendor.
2. Turn the two tabs on the chiller housing and
swing the chiller cover door all the way up.
3. With a finger in the removable screen handle, lift
it up slightly and slide it towards you.
4. A vacuum attachment with a brush, or a bristle
brush, may be used to remove dirt and lint from
screen.
CAUTION: Condenser fins are sharp!
5. Remove dust from the condenser fins and coils.
Do not damage the fins or coils.
6. Do not use water or other liquid chemicals or
solvents.
7. Reinstall the clean and dry removable screen by
sliding it back into the holder.
8. Close door on chiller housing and turn the two
tabs to hold door closed.
9. Clean the floor under the vendor with the brush,
removing any obstructions such as cardboard
and wrappers.
10. Close the vendor door.
8.6 CLEANING THE VENDOR EXTERIOR
Clean the vendor exterior as necessary using mild
household cleaners and water. Dampen a cloth or
sponge with the cleaning solution and gently wipe
clean the exterior.
1. Do not use chemicals or solvents. These can
damage paint, plastic trim and decals.
2. Do not use abrasive cleaners.
3. Do not use a water jet.
4. Do not let water or cleaning solutions contact
electrical or electronic components.
5. Clean the glass front inside and out with a good
window cleaner.
8.7 CLEANING THE VENDOR INTERIOR
Clean the interior using mild household cleaners and
water. Dampen a cloth or sponge with the cleaning
solution and gently wipe the interior surfaces clean.
Some vendors use a door liner made from ABS
plastic. This liner will crack if chemical solvents or
harsh detergents are used.
1. Unplug the vendor from the power socket.
2. Open the vendor door.
3. Do not use chemicals or solvents. These can
damage paint, extruded plastic parts and other
plastic parts.
4. Do not use abrasive cleaners.
5. Do not use a water jet.
6. Do not let water or cleaning solutions contact
electrical or electronic components.
7. Allow to air dry, or place a window fan on the
floor in front of the open interior.
8. When dry, plug in the vendor.
8.8 LUBRICATION WITH LITHIUM GREASE
Once a year the bottle tray rail ball bearings and door
moving parts should be lubricated with grease.
a. Pull out the tray. The tray rail is constructed of
telescoping channel sections. Apply a very light
coating of white lithium grease on the outside of
the first two sections, along the top and bottom
edges.
b. Apply grease on the inside of the last two
sections along the top and bottom.
c. Apply grease (or similar lubricant) to the door
lock bolt threads and the door hinges as
necessary.
d. Wipe off excess grease. No other lubrication is
required.
8.9 LAMP REPLACEMENT
Replacing Optional Fluorescent Bulbs
1. Unplug the vendor from the wall.
2. Open the door.
3. If applicable, remove the lamp cover from over
the defective bulb.
4. Turn bulb one-quarter turn and, at both ends at
the same time, slide out through the slots in bulb
sockets.
5. Remove one of the two black end caps from the
clear protective tube. Slowly remove defective
bulb by sliding it out of the tube.
6. Dispose of bulb properly.
7. Slowly insert new bulb into clear protective tube,
turning the bulb so the pins are centered in the
opening in the black end cap. Install the second
black end cap, centering the opening over the
pins.
8. Install the bulb by inserting bulb pins at both ends
at the same time through slots in bulb sockets,
then turn bulb one-quarter turn.
9. If applicable, reinstall the lamp cover.
10. Plug in the vendor to test the lamp.
11. Close the vendor door.
To Next Page
Loading...
