L0118G
1-3
1.5 GENERAL SPECIFICATIONS
Operating Environment
These AMS vendors are designed for indoor use only.
Indoor temperatures must be between 35°F (1°C) and
110°F (43°C). Maximum temperature for vendors with
perishable food is 100F (38C). The vendor should not
be located in an area where it may be subjected to
direct sunlight, a water jet, or rain.
Cabinet Physical Dimensions: Model 35
(Refer to Figure 1.2)
33 3/4”W x 72”H x 36”D
(89 cm x 183 cm x 91 cm)
Cabinet Weight: Model 35
Snack Approx. 490 lbs. (223 kg)
w/ chiller 580 lbs. (264 kg)
All Low Temp Versions: Approx. 555 lbs. (252 kg)
Unit Capacity: Model 35
(Refer to Section 1.6)
Capacity depends on configuration:
120 units min.
1152 units max.
Cabinet Physical Dimensions: Model 39
(Refer to Figure 1.3)
39”W x 72”H x 36”D
(99 cm x 183 cm x 91 cm)
Cabinet Weights: Model 39
Snack Approx. 544 lbs. (247 kg)
w / chiller 634 lbs. (288 kg)
All Low Temp Versions: Approx. 585 lbs. (266 kg)
Unit Capacity: Model 39
(Refer to Section 1.6)
Capacity depends on configuration:
150 units min.
1440 units max.
Models 35 and 39 Power Requirements
United States,
Canada and Mexico: 120 VAC, 60 Hz
International: 230 VAC, 50/60 Hz
Basic Unit: 3 amps @ 120 VAC
1.6 amps @230 VAC
Refrigerated Snack: 7 amps @ 120 VAC
3.7 amps @230 VAC
Visi-Combo and 10.8 amps @120 VAC
Visi-Diner and Milk: 5.6 amps @230 VAC
ENERGY STAR
MODELS: 5 amps @120 VAC
Energy Consumption
Daily energy consumption varies considerably due to
temperature, humidity, usage, load schedule, etc.
Based on our testing done to ANSI/ ASHRAE
Standard test conditions (75°F @ 45% RH), the
following values are presented for comparison only.
Low-Temp vendor: 10.48 KWH/day (39”)
Low-Temp vendor: 9.60 KWH/day (35”)
ENERGY STAR Models: 4.18 KWH/day (39”)
(See Section 1.3) 3.18 KWH/day (35”)
Refrigerant Specifications
Snack: 1/ 4 HP, R-134a, 7.2 oz. (.20 kg)
Visi-Combo and
Visi-Diner/Milk: 0.6 HP, R-134a, 10 oz. (.28 kg)
ENERGY STAR 1/2 HP, R-134a, 8.1 oz. (.23 kg)
Coin Changers and Bill Validators
AMS vendors will support all Multi-Drop Bus (MDB)
coin changers, bill validators and card readers. Where
applicable, it will also support coin changers using the
“Executive” communications protocol.
MDB Peripheral Levels Supported
The Sensit 3 Control Electronics are designed to work
with MDB Devices at the following Function and
Option Levels:
Coin Changers – Level 3 Changers are supported:
The Alternate Payout Method is supported,
but neither the Extended Diagnostics
Command nor the Controlled Manual
Fill/Payout features are supported.
Bill Validators – Level 1 Validators are supported
Cashless Devices – Level 2 Devices are supported
To Next Page
Loading...
