AMX MST-1001 Configuration Manual

Programming
46
Modero S Series Touch Panels - Configuration & Programming Manual
Page Commands (Cont.)
@PHP Set the hide effect position - Only 1 coordinate is ever needed for an effect; however, the command will specify both. This
command sets the location at which the effect will end at.
•Syntax:
"'@PHP-<popup page name>;<x coordinate>,<y coordinate>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
•Example:
SEND_COMMAND Panel,"'@PHP-Popup1;75,0'"
Sets the Popup1 hide effect x-coordinate value to 75 and the y-coordinate value to 0.
@PHT Set the hide effect time for the specified popup page.
•Syntax:
"'@PHT-<popup page name>;<hide effect time>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
hide effect time = Given in 1/10ths of a second.
•Example:
SEND_COMMAND Panel,"'@PHT-Popup1;50'"
Sets the Popup1 hide effect time to 5 seconds.
@PPA Close all popups on a specified page. If the page name is empty, the current page is used. Same as the ’Clear Page’ command in
TPDesign4.
•Syntax:
"'@PPA-<page name>'"
•Variables:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
•Example:
SEND_COMMAND Panel,"'@PPA-Page1'"
Close all pop-ups on Page1.
@PPF Deactivate a specific popup page on either a specified page or the current page. If the page name is empty, the current page is
used (see example 2). If the popup page is part of a group, the whole group is deactivated. This command works in the same way
as the ’Hide Popup’ command in TPDesign4.
•Syntax:
"'@PPF-<popup page name>;<page name>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
•Example:
SEND_COMMAND Panel,"'@PPF-Popup1;Main'"
•Example 2:
SEND_COMMAND Panel,"'@PPF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.
@PPG Toggle a specific popup page on either a specified page or the current page. If the page name is empty, the current page is used
(see example 2). Toggling refers to the activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
•Syntax:
"'@PPG-<popup page name>;<page name>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
•Example:
SEND_COMMAND Panel,"'@PPG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the ’Main’ page from one state to another (On/Off).
•Example:
SEND_COMMAND Panel,"'@PPG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).

AMX MST-1001 Specifications

General

Aspect ratio	16:9
Screen shape	Flat
Display diagonal	10 \
Touchscreen type	Tabletop
Display brightness	350 cd/m²
Display resolution	1280 x 800 pixels
Display technology	LED
Touchscreen technology	Resistive
Viewable size diagonal	256 mm
Contrast ratio (typical)	800:1
Display number of colors	16.78 million colors
Product color	Black
Ethernet LAN (RJ-45) ports	1
Display viewable area (HxV)	136 x 217 mm
Power supply type	DC
Power consumption (standby)	4.5 W
Power consumption (typical)	7.5 W
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 85 %
Operating relative humidity (H-H)	20 - 85 %
Wall mountable	No
HDMI ports quantity	0
Graphics card	AMX G4
Internal memory	512 MB
Internal memory type	DDR
RMS rated power	1.5 W

Weight and Dimensions

Depth (without stand)	103 mm
Width (without stand)	264 mm
Height (without stand)	157 mm
Weight (without stand)	5530 g