AMX MST-1001 Configuration Manual

Programming
47
Modero S Series Touch Panels - Configuration & Programming Manual
Page Commands (Cont.)
@PPK Kill a specific popup page from all pages. Kill refers to the deactivating (Off) of a popup window from all pages. If the pop-up page
is part of a group, the whole group is deactivated. This command works in the same way as the 'Clear Group' command in
TPDesign 4.
•Syntax:
"'@PPK-<popup page name>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
•Example:
SEND_COMMAND Panel,"'@PPK-Popup1'"
Kills the popup page ’Popup1’ on all pages.
@PPM Set the modality of a specific popup page to Modal or NonModal. A Modal popup page, when active, only allows you to use the
buttons and features on that popup page. All other buttons on the panel page are inactivated.
•Syntax:
"'@PPM-<popup page name>;<mode>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
mode = NONMODAL converts a previously Modal popup page to a NonModal.
MODAL converts a previously NonModal popup page to Modal.
modal = 1 and non-modal = 0
•Example:
SEND_COMMAND Panel,"'@PPM-Popup1;Modal'"
Sets the popup page ’Popup1’ to Modal.
•Example:
SEND_COMMAND Panel,"'@PPM-Popup1;1'"
Sets the popup page ’Popup1’ to Modal.
@PPN Activate a specific popup page to launch on either a specified page or the current page. If the page name is empty, the current
page is used (see example 2). If the popup page is already on, do not re-draw it. This command works in the same way as the
’Show Popup’ command in TPDesign4.
•Syntax:
"'@PPN-<popup page name>;<page name>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
•Example:
SEND_COMMAND Panel,"'@PPN-Popup1;Main'"
Activates ’Popup1’ on the ’Main’ page.
•Example:
SEND_COMMAND Panel,"'@PPN-Popup1'"
Activates the popup page ’Popup1’ on the current page.
@PPT Set a specific popup page to timeout within a specified time. If timeout is empty, popup page will clear the timeout.
•Syntax:
"'@PPT-<popup page name>;<timeout>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
timeout = Timeout duration in 1/10ths of a second.
•Example:
SEND_COMMAND Panel,"'@PPT-Popup1;30'"
Sets the popup page ’Popup1’ to timeout within 3 seconds.
@PPX Close all popups on all pages. This command works in the same way as the 'Clear All' command in TPDesign 4.
•Syntax:
"'@PPX'"
•Example:
SEND_COMMAND Panel,"'@PPX'"
Close all popups on all pages.
@PSE Set the show effect for the specified popup page to the named show effect.
•Syntax:
"'@PSE-<popup page name>;<show effect name>'"
•Variables:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
show effect name = Refers to the popup effect name being used.
•Example:
SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'"
Sets the Popup1 show effect name to ’Slide from Left’.

AMX MST-1001 Specifications

General

Aspect ratio	16:9
Screen shape	Flat
Display diagonal	10 \
Touchscreen type	Tabletop
Display brightness	350 cd/m²
Display resolution	1280 x 800 pixels
Display technology	LED
Touchscreen technology	Resistive
Viewable size diagonal	256 mm
Contrast ratio (typical)	800:1
Display number of colors	16.78 million colors
Product color	Black
Ethernet LAN (RJ-45) ports	1
Display viewable area (HxV)	136 x 217 mm
Power supply type	DC
Power consumption (standby)	4.5 W
Power consumption (typical)	7.5 W
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 85 %
Operating relative humidity (H-H)	20 - 85 %
Wall mountable	No
HDMI ports quantity	0
Graphics card	AMX G4
Internal memory	512 MB
Internal memory type	DDR
RMS rated power	1.5 W

Weight and Dimensions

Depth (without stand)	103 mm
Width (without stand)	264 mm
Height (without stand)	157 mm
Weight (without stand)	5530 g