Argo-Hytos OPCom - 6 Transport and Storage

69 pages

Save Page as PDF

To Next Page

To Previous Page

Subject to change · V 2.02.20 · EN

Page 14

www.argo-hytos.com

6. Transport and storage

There are no special transport instructions for this product.

 However, observe the instructions in Chapter 2, “Safety instructions”.

 For storage and transport, observe the speciﬁed environmental conditions stated in the technical data.

Main Page

Default Chapter2
- Table of Contents2
- Contents2
1 About this Documentation5
- Applicability of this Documentation5
- Required and Supplementary Documentation5
- Presentation of Information5
- Safety Instructions5
- Symbols6
- Terms6
- Abbreviations6
2 Safety Instructions7
- About this Chapter7
- Intended Use7
- Improper Use7
- Reasonably Foreseeable Misuse7
- Qualification of Personnel7
- General Safety Instructions8
- Product and Technology Related Safety Instructions8
- Indications on the Product8
3 General Instructions10
4 Scope of Delivery11
5 About this Product12
- Functional Description12
- Component Overview13
- Identification of the Product13
6 Transport and Storage14
7 Assembly15
- Operating Site15
- Hydraulic Connection15
- Mounting16
- Mechanical Stress17
8 Electrical Connection18
- Pin Assignment (View from Above)18
9 Commissioning19
- Before Commissioning19
10 Start Screen20
- Status Display20
- Time Display20
- Displayed Standard20
- Ordinal Numbers20
11 Menu and Operation21
- Menu Structure22
- Operating Modes23
- Time-Controlled Measurement23
- Digital I/O23
- Button23
- Automatic24
- Alarm Configuration24
- Alarm Type24
- Standard Alarm24
- Filter Mode25
- Temperature Alarm25
- Alarm Memory25
- Low-Pass Filter25
- Configuration Analog26
- Standard27
- Configuration Flow27
- Automatic27
- Fix27
- Communication27
- Type27
- Baud Rate CAN28
- Node ID CAN28
- Baud Rate RS23228
- Automatic Transmission28
- Configuration Display29
- Sensor Parameter29
- Measurement Results29
- Electronics29
- Operating Hours30
- Error Info30
- Flow Settings30
- Language30
12 Calibration31
- Calibration Note31
13 Analog Current Output (432
- Measurement Without Load Resistance32
- Measurement with Load Resistance32
- Configuration32
- Conversion of the Analog Current Output to the Ordinal Number32
- Sequential Data Output for ISO 4406:17 and SAE as 4059E33
14 Switching Inputs and Outputs34
- Digital Input34
- Switching Output34
- Option 134
- Option 235
15 Communication RS23236
- Interface Parameters36
- Read Commands36
- Configuration Commands38
- Checksum Calculation (CRC)41
16 Communication CAN42
- Canopen42
- Canopen Object Dictionary" in General43
- Canopen Communication Objects43
- Service Data Object (SDO)44
- Process Data Object (PDO)46
- PDO Mapping46
- Canopen Object Dictionary" in Detail48
- Can J193953
17 Classification Systems54
- Definition of Particle Sizes54
- Cleanliness Classes According to ISO 4406:1754
- Cleanliness Classes According to SAE as 4059E55
- Cleanliness Classes According to NAS 163856
- Cleanliness Classes According to GOST 1721657
18 Maintenance and Repair58
- Maintenance58
- Repair58
19 Decommissioning, Disassembly, Disposal59
- Environment59
20 Accessories60
21 Troubleshooting61
22 Faq62
23 Technical Data64
- Dimensional Drawing65
24 Appendix66
- Cable Lengths66
- Coding of Error Bits66
- Particle Contaminations68

Other manuals for Argo-Hytos OPCom

Manual47 pages

Argo-Hytos OPCom - 6 Transport and Storage

Table of Contents

Other manuals for Argo-Hytos OPCom