Binder 9020-0338

To Next Page

To Previous Page

KBW (E6) 11/2016 page 86/147

Entry of digits

Entry of special characters

To confirm the password after the entry, repeat the

entry and press the Confirm icon.

Main Page

Default Chapter1
- Operating Manual1
- Table of Contents2
1 Safety6
- Legal Considerations6
- Structure of the Safety Instructions6
- Localization / Position of Safety Labels on the Chamber8
- Type Plate9
- General Safety Instructions on Installing and Operating the Chambers10
- Intended Use12
- Operating Instructions12
- Measures to Prevent Accidents13
2 Chamber Description and Overview14
- Chamber Description14
- Chamber Overview15
- Instrument Panel15
- Lateral Control Panels16
3 Completeness of Delivery, Transportation, Storage, and Installation17
- Unpacking, and Checking Equipment and Completeness of Delivery17
- Guidelines for Safe Lifting and Transportation18
- Storage18
- Location of Installation and Ambient Conditions18
4 Installation and Connections20
- Spacer for Wall Distance20
- Mounting the Flexible Tilt Protection Kit (KBW 400)21
- Installation and Connection of the Light Cassettes22
- Electrical Connection23
5 Functional Overview of the Mb2 Chamber Controller24
- Operating Functions in Normal Display25
- Display Views: Normal Display, Program Display, Chart-Recorder Display26
- Controller Icons Overview27
- Operating Modes29
- Controller Menu Structure30
- Principle of Controller Entries33
- Performance During and after Power Failures33
- Performance When Opening the Door34
6 Start up34
- Turning on the Chamber34
- Controller Settings Upon Start up35
7 Set-Point Entry in "Fixed Value" Operating Mode36
- Set-Point Entry through the "Setpoints" Menu37
- Direct Setpoint Entry Via Normal Display38
- Automatic Correction of the Actual Value When Turning on or off the Illumination38
- Light Commutation and Special Controller Functions Via Operation Lines39
8 Timer Program: Stopwatch Function40
- Starting a Timer Program40
  - Performance During Program Delay Time41
- Stopping a Running Timer Program41
  - Pausing a Running Timer Program41
  - Cancelling a Running Timer Program42
- Performance after the End of the Program42
9 Time Programs43
- Starting an Existing Time Program43
  - Performance During Program Delay Time44
- Stopping a Running Time Program45
  - Pausing a Running Time Program45
  - Cancelling a Running Time Program45
- Performance after the End of the Program45
- Creating a New Time Program46
- Program Editor: Program Management46
- Section Editor: Section Management48
- Value Entry for a Program Section51
10 Week Programs59
- Starting an Existing Week Program59
- Cancelling a Running Week Program60
- Creating a New Week Program61
- Program Editor: Program Management62
- Section Editor: Section Management63
  - Add a New Section64
  - Copy and Insert or Replace a Section65
- Value Entry for a Program Section65
- Deleting a Week Program68
11 Notification and Alarm Functions69
- Notification and Alarm Messages Overview69
  - Notifications69
  - Alarm Messages70
- State of Alarm70
- Resetting an Alarm, List of Active Alarms71
- Tolerance Range Settings71
- Activating / Deactivating the Audible Alarm (Alarm Buzzer)72
12 Temperature Safety Devices73
- Over Temperature Protective Device (Class 1)73
- Overtemperature Safety Controller Class 3.173
- Temperature Safety Device Class 3.3 (Option)76
  - Temperature Safety Device Class 3.177
  - Temperature Safety Device Class 3.278
13 User Management79
- Authorization Levels and Password Protection79
- Log in82
- Log out83
- User Change83
- Password Assignment and Password Change84
- Activation Code89
14 General Controller Settings90
- Selecting the Controller's Menu Language90
- Selecting the Temperature Unit90
- Setting Date and Time91
- Display Configuration93
  - Adapting the Display Parameters93
  - Touchscreen Calibration95
- Network and Communication96
- USB Menu102
15 General Information103
- Service Contact Page103
- Current Operating Parameters103
- Event List104
- Technical Chamber Information105
16 Chart Recorder Display106
- Views106
- Setting the Parameters108
17 Defrosting at Refrigerating Operation110
18 Illumination System111
- Illumination for Optimal Plant Growth111
- Adjustable Light Cassettes111
- Illumination Control113
19 Options114
- Communication Software APT-COM™ 3 Datacontrolsystem (Option)114
- RS485 Interface (Option)114
- Data Logger Kit (Option)114
- Analog Outputs for Temperature (Option)115
- Zero-Voltage Relay Alarm Outputs for Temperature (Option)115
- Water Protected Internal Socket (Option)116
- Additional Flexible Pt 100 Temperature Sensor (Available Via BINDER INDIVIDUAL Customized Solutions)117
- Object Temperature Display with Flexible Pt 100 Temperature Sensor (Option)117
20 Maintenance, Cleaning, and Service118
- Maintenance Intervals, Service118
- Replacement of the Fluorescent Tubes119
- Cleaning and Decontamination119
  - Cleaning120
  - Decontamination121
- Sending the Chamber Back to BINDER Gmbh122
21 Disposal123
- Disposal of the Transport Packing123
- Decommissioning123
- Disposal of the Chamber in the Federal Republic of Germany123
- Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany125
- Disposal of the Chamber in Non-Member States of the EU126
22 Troubleshooting127
23 Technical Description129
- Factory Calibration and Adjustment129
- Over Current Protection129
- Definition of Usable Volume129
- Technical Data130
- Equipment and Options (Extract)132
- Spare Parts and Accessories (Extract)133
- Dimensions KBW 240134
- Dimensions KBW 400135
- Dimensions KBW 720136
24 Certificates and Declarations of Conformity137
- EU Declaration of Conformity137
  - Certificate for the GS Mark of Conformity of the "Deutsche Gesetzliche Unfallversicherung E.V." (German Social Accident Insurance) DGUV139
25 Product Registration141
26 Contamination Clearance Certificate142
- For Chambers Located Outside USA and Canada142
- For Chambers Located in USA and Canada145

Binder 9020-0338 - Page 86

Table of Contents

Related product manuals