Case 8000 Series - 3.4 Initial Configuration Commands

3.4 Initial Configuration Commands
After cold start, Router is placed in an initial state ready for configuring,
with the default configuration defined in Appendix B.
Cold start normally only takes place when the card is first installed.
However, if at any time it is found necessary to go back to the default
configuration, then a cold start can be performed by deleting the
configuration files
Tgateconfig<n> and IPrtrconfig<n> from disk B (see
Series 8000 Xpress PSE (V.7) User Guide, Section 5.3.5), where
n is the slot
number in which the Router resides. Then a card reset may be executed;
see the Series 8000 installation guide.
From the Manage Application screen of the Series 8000 Node Manager, set
up an entry for the Router port, and use this to call the Router manager.
Alternatively, from a Triple-X PAD or the Series 8000 manager 'mini pad',
make an X.25 call using sub-address 99, which calls the Router manager
direct.
The X.121 address is:
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
DNIC
a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a
Node
number
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Application port
number as defined by
Series 8000 manager
a a a a a a a a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a a a a a a a a
1
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
2
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
3
a a a a a a a a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a a a a a a a a
4
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
5
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
6
a a a a a a a a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a a a a a a a a
7
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
8
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
9
a a a a a a a a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a a a a a a a a
10
a a a a a a a
a
a a a a a
a
a
a a a a a
a
a
a a a a a
a
a a a a a a a
11
The default X.121 is shown in Appendix B.
In both of the above cases a password is requested. Initially, this is simply
carriage return. The Router then requests that a terminal type is specified.
If the terminal type you are using is not listed, or is not compatible with
one of the types listed, select the
Define option to define your terminal (see
Section 3.5).
The actual configuration depends upon the application that Router is being
used for. Detailed below is a suggested order of configuration. Commands
shown in bold are the manager commands that gain access to the relevant
configuration screens; commands in brackets are their shortened form.
X870-300351 Issue 1 3-4 Rev.0