Name: Chromalox 1020
Brand: Chromalox
Rating: 4 (1 reviews)

To Next Page

To Previous Page

1020/1030 Rail Isolation Chart

PSU

Universal

Input Relay SSR Linear

RS485

Comms

Non-

Isolated

Digital

Input

Isolated

Digital

Input

Conﬁguration

Port

PSU

Universal

Input

Relay

SSR

Linear

RS485 Comms

Non-Isolated

Digital Input

Isolated

Digital Input

Conﬁguration

Port

Not Applicable

No Isolation

Reinforced Isolation

Default Chapter4
- Table of Contents4
Chapter 1 Installation7
- Unpacking7
- Cleaning7
- Installation7
Chapter 2 Electrical Installation8
- Installation Considerations8
- AC Power Wiring8
- Wire Installation8
- Use of Shielded Cable8
- Noise Suppression at Source8
- Sensor Placement9
- Panel Wiring9
- Terminal Wiring10
- Power Connection10
Chapter 3 Powering up13
- Powering up Procedure13
- First Power up or Factory Default13
- Auto-Tune13
- Front Panel13
- General Navigation & Editing14
- Mode (or Menu) Structure14
- Returning to Perator Mode14
- Mode and Access and Lock Codes14
- Use of the Controller for Non-Temperature Applications14
- Controller Transmitter Function14
- User Mode & Screens on Standard & Extruction Models15
- Warnings & Messages16
Chapter 4 Initial Default Settings18
- Factory Reset Procedure18
Chapter 5 Setup Mode19
- Navigating the Setup Screens19
Chapter 6 Advanced Configuration Mode21
Chapter 7 User Mode22
- User Menu22
- Input Menu23
- User Calibration Menu24
- Outputs Menu24
- Control Menu (Standard Model)25
- Control Menu (Extrusion Model)26
- Setpoint Menu (Standard Model)27
- Setpoint Menu (Extrusion Model)27
- Alarm Menu28
- Communications Menu28
- Display Menu29
- Operator Screens Menu29
- Information Menu29
- Exiting the Advanced Configuration Mode29
Chapter 8 Calibration Mode30
- Single Point Calibration (PV Offset)30
- Two Point Calibration30
- Base Input Calibration31
- Calibration Check31
- Base Calibration Procedure31
- Calibrating the MV Input31
- Calibrating Other Input Types32
- Calibration Input States32
- Calibration Progress32
- Calibration Modbus Addresses32
Chapter 9 Automatic Tuning33
- Running the Pre-Tune33
- Running Tune at SP33
- Tuning at SP Troubleshooting33
- Tuning at SP for Heat and Cool34
Chapter 10 Digital Input Operation35
Chapter 11 Timer Feature37
- Timer Feature37
- Delay, Ramp & Timer Diagram37
Chapter 12 Extrusion Model Only Features38
- Non-Linear Cooling Function38
- Method38
- Parameter Adjustment40
- Soft Start Function40
- Extrusion Only Parameters in the Control Menu41
Chapter 13 Limiter Models42
- Introduction to the Limiter Model42
- Limiter Modbus Communications42
- Limiter Digital Input42
- Limiter Operator Mode & Screens43
- Limiter Output Latching43
- Limiter Setup Mode Parameters43
- Limiter Advanced Configuration Parameters46
- Limiter Input Menu46
- Limiter User Calibration Menu46
- Limiter Outputs Menu47
- Limiter Communications Menu49
- Limiter Display Menu49
- Limiter Information Menu49
- Limiter Exiting from Advanced Configuration Mode49
Chapter 14 Configuration Software50
- Introduction50
- Connectivity Requirements50
- Installing & Accessing the Configuration Program51
- Getting Started51
- Troubleshooting the Series 20 Configurator52
- Getting Started (Continued)53
- Navigating the Configurator54
Chapter 15 Serial Communications57
- Supported Protocol57
- RS485 Configuration57
- RS485 Device Addressing57
- Link Layer57
- Supported Modbus Functions58
- Function Descriptions58
- Function 03/04 Read Holding/Input Registers58
Chapter 16 Modbus Addresses60
- Input Parameters60
- Standard Extrusion Modbus Addresses61
- Limiter Modbus Addresses69
Chapter 17 Specifications74
Chapter 18 Glossary76
Chapter 19 Order Tables84

Questions and Answers:

Need help?

Do you have a question about the Chromalox 1020 and is the answer not in the manual?

Chromalox 1020 Specifications

General

Brand	Chromalox
Model	1020
Category	Temperature Controller
Language	English

Related product manuals

Chromalox 1020 User Manual

Table of Contents

Questions and Answers:

Chromalox 1020 Specifications

Related product manuals