Chromalox 1020 User Manual

86 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #2 background image

Loading...

Page #2 background image

Table of Contents

Default Chapter4
- Table of Contents4
Chapter 1 Installation7
- Unpacking7
- Cleaning7
- Installation7
Chapter 2 Electrical Installation8
- Installation Considerations8
- AC Power Wiring8
- Wire Installation8
- Use of Shielded Cable8
- Noise Suppression at Source8
- Sensor Placement9
- Panel Wiring9
- Terminal Wiring10
- Power Connection10
Chapter 3 Powering up13
- Powering up Procedure13
- First Power up or Factory Default13
- Auto-Tune13
- Front Panel13
- General Navigation & Editing14
- Mode (or Menu) Structure14
- Returning to Perator Mode14
- Mode and Access and Lock Codes14
- Use of the Controller for Non-Temperature Applications14
- Controller Transmitter Function14
- User Mode & Screens on Standard & Extruction Models15
- Warnings & Messages16
Chapter 4 Initial Default Settings18
- Factory Reset Procedure18
Chapter 5 Setup Mode19
- Navigating the Setup Screens19
Chapter 6 Advanced Configuration Mode21
Chapter 7 User Mode22
- User Menu22
- Input Menu23
- User Calibration Menu24
- Outputs Menu24
- Control Menu (Standard Model)25
- Control Menu (Extrusion Model)26
- Setpoint Menu (Standard Model)27
- Setpoint Menu (Extrusion Model)27
- Alarm Menu28
- Communications Menu28
- Display Menu29
- Operator Screens Menu29
- Information Menu29
- Exiting the Advanced Configuration Mode29
Chapter 8 Calibration Mode30
- Single Point Calibration (PV Offset)30
- Two Point Calibration30
- Base Input Calibration31
- Calibration Check31
- Base Calibration Procedure31
- Calibrating the MV Input31
- Calibrating Other Input Types32
- Calibration Input States32
- Calibration Progress32
- Calibration Modbus Addresses32
Chapter 9 Automatic Tuning33
- Running the Pre-Tune33
- Running Tune at SP33
- Tuning at SP Troubleshooting33
- Tuning at SP for Heat and Cool34
Chapter 10 Digital Input Operation35
Chapter 11 Timer Feature37
- Timer Feature37
- Delay, Ramp & Timer Diagram37
Chapter 12 Extrusion Model Only Features38
- Non-Linear Cooling Function38
- Method38
- Parameter Adjustment40
- Soft Start Function40
- Extrusion Only Parameters in the Control Menu41
Chapter 13 Limiter Models42
- Introduction to the Limiter Model42
- Limiter Modbus Communications42
- Limiter Digital Input42
- Limiter Operator Mode & Screens43
- Limiter Output Latching43
- Limiter Setup Mode Parameters43
- Limiter Advanced Configuration Parameters46
- Limiter Input Menu46
- Limiter User Calibration Menu46
- Limiter Outputs Menu47
- Limiter Communications Menu49
- Limiter Display Menu49
- Limiter Information Menu49
- Limiter Exiting from Advanced Configuration Mode49
Chapter 14 Configuration Software50
- Introduction50
- Connectivity Requirements50
- Installing & Accessing the Configuration Program51
- Getting Started51
- Troubleshooting the Series 20 Configurator52
- Getting Started (Continued)53
- Navigating the Configurator54
Chapter 15 Serial Communications57
- Supported Protocol57
- RS485 Configuration57
- RS485 Device Addressing57
- Link Layer57
- Supported Modbus Functions58
- Function Descriptions58
- Function 03/04 Read Holding/Input Registers58
Chapter 16 Modbus Addresses60
- Input Parameters60
- Standard Extrusion Modbus Addresses61
- Limiter Modbus Addresses69
Chapter 17 Specifications74
Chapter 18 Glossary76
Chapter 19 Order Tables84

Questions and Answers:

Need help?

Do you have a question about the Chromalox 1020 and is the answer not in the manual?

Chromalox 1020 Specifications

General

Brand	Chromalox
Model	1020
Category	Temperature Controller
Language	English

Related product manuals

Preview: Chromalox 2110

Preview: Chromalox 2104