Cisco 2431 - IAD Router

124 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

A-12

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Appendix A Cisco IAD2430 Series Configuration Examples

Sample Configuration: Cisco 2432-24FXS with VIC2-4FXO and QoS

Table of Contents

Default Chapter3
- Table of Contents3
- Configuring3
- Entering5
- Recovering Boot and System Images5
- Debug Commands6
- Exiting6
Preface7
- To Access Online User Documentation (PDF and HTML Formats)8
  - Document Organization8
  - Obtaining Documentation and Submitting a Service Request9
Chapter 1 Understanding Interface Numbering and Cisco IOS Software Basics11
- Identifying Cisco IAD2430 Models11
- Port Numbering Conventions15
- Understanding Cisco IOS Software Basics15
- Upgrading to a New Cisco IOS Release18
- Cisco IAD2430 Series Deployment Scenarios19
- Where to Go Next20
Chapter 2 Using the Setup Command Facility21
- Before Powering on Your Cisco IAD21
- The Setup Command Facility22
- Interface Card22
- Configuring Global Parameters22
- Configuring Controller and Interface Parameters25
- Completing the Configuration33
Chapter 3 Configuring with the Command-Line Interface33
Configuring the Hostname and Password36
- Verifying the Hostname and Password37
Configuring Fast Ethernet Interfaces38
Configuring Network Clock39
Configuring T1/E1 Interfaces41
- Configuring Channel Groups on T1/E1 to Support Data42
- Configuring Channel Groups on T1/E1 to Support Data under SHDSL Controller44
- Configuring Digital Voice on T1/E145
  - Configuring Switch Types for ISDN PRI Q.931 Support45
  - Configuring DS0 Groups for cas45
- Configuring TDM Cross-Connect50
Configuring a WIC-1DSU-T1/E1 Serial WAN Interface Card54
- Interfaces56
- Half-Duplex Timer Commands56
- Clock Rate Settings for 1-Port/2-Port Serial WAN Interface Card in Synchronous Mode57
- Clock Rate Settings for 2-Port Synchronous Serial57
- Clock Rate Settings for 4-Port Synchronous Serial57
Configuring a WIC-1T or WIC-2T Serial WAN Interface Card58
Configuring a VIC2-2FXO or VIC2-4FXO Voice Interface Card58
Configuring a VIC2-2FXS or VIC2-4FXS Voice Interface Card60
Configuring ATM T1-WAN Ports62
- Verifying Your ATM Interface Configuration65
Configuring 1-Port ADSL/SHDSL WAN Interface Card66
- Configuration Tasks66
  - Configuring the ADSL/SHDSL Port on the ADSL and SHDSL WAN Interface Card66
  - Verifying ATM Configuration69
Configuring a VIC2-2BRI-NT/TE Card70
- Saving Configuration Changes72
Chapter 4 Configuring Voice over IP75
- Prerequisites75
- Configuring the Voice Interface76
- Voip Configuration Examples78
  - FXS-To-FXS Connection78
Appendix85
Cisco IAD2430 Series Configuration Examples85
- Sample Configuration: Cisco IAD2435-8FXS85
- A P P E N D I X a Cisco IAD2430 Series Configuration Examples86
- Sample Configuration: Cisco 2430-24FXS87
- Sample Configuration: Cisco 2431-1T1/E1 with WIC-2T90
- Sample Configuration: Cisco 2432-24FXS with VIC2-4FXO and Qos92
Appendix97
Formatting the Flash Memory97
- Formatting Procedures for Flash Memory97
  - Formatting Procedures97
    - Determining the File System on Flash Memory97
    - ROM Monitor97
- File and Directory Operations101
  - Operations for Use with Class B Flash File System101
Appendix B Formatting the Flash Memory98
- Formatting Flash Memory as a Class B Flash File System99
Mode99
- Formatting Flash Memory as a Class C File System100
Note Slot0 Is Not Supported on the IAD2435 IAD101
- System Flash Directory102
- File Length102
- C2430-Is-Mz102
- C2430-Telcoent-Mz102
- Operations for Use with Class C Flash File System104
Appendix111
Using the ROM Monitor111
- Entering the ROM Monitor Mode111
- ROM Monitor Commands112
Appendix C Using the ROM Monitor113
- Command Descriptions113
- Recovering Boot and System Images114
  - Using the Xmodem Command114
  - Using the Tftpdnld -R Command115
- Configuration Register116
  - Changing the Configuration Register Manually116
  - Changing the Configuration Register Using Prompts116
- Console Download117
  - Command Description117
  - Error Reporting118
- Debug Commands118
- Exiting the ROM Monitor119
I N D E X121
- PSTN Gateway Access Using FXO Connection Example122
- PSTN Gateway Access Using FXO Connection124

Other manuals for Cisco 2431 - IAD Router

Hardware Installation Guide88 pages

Related product manuals

Preview: Cisco NCS 2006

Preview: Cisco NCS 2000 series

Cisco NCS 2000 series

Preview: Cisco ASA

Preview: Cisco 7606

Preview: Cisco SCE8000

Preview: Cisco ONS 15454

Cisco ONS 15454

Preview: Cisco 1000 Series

Cisco 1000 Series

Preview: Cisco Linksys NSLU2

Cisco Linksys NSLU2

Preview: Cisco ONS 15454 M12

Cisco ONS 15454 M12

Preview: Cisco Firepower 9300

Cisco Firepower 9300

Cisco linksys PLTK300

Preview: Cisco Firepower 1010 Series

Cisco Firepower 1010 Series