Cisco WAP125 Administrator's Guide

A dialog box appears confirming the firmware image switch and subsequent reboot.
Step 3
Click OK to proceed.
The process may take several minutes, during which time the WAP device is unavailable. Do not power down the WAP
device while the image switch is in process. When the image switch is complete, the WAP device restarts. The WAP
device resumes normal operation with the same configuration settings it had before the upgrade.
HTTP/HTTPS Upgrade
To upgrade using HTTP/HTTPS:
Step 1
Select HTTP/HTTPS as the transfer method.
Step 2
Click Browse and locate the firmware image file on your network.
The firmware upgrade file supplied must be a tar file. Do not attempt to use bin files or files of other formats for the
upgrade; these types of files do not work.
Step 3
Click Upgrade to apply the new firmware image.
Uploading the new firmware may take several minutes. Do not refresh the page or navigate to another page while
uploading the new firmware, or the firmware upload is aborted. When the process is complete, the WAP device restarts
and resumes normal operation.
Step 4
To verify that the firmware was upgraded successfully, log into the web-based Configuration Utility, open the Upgrade
Firmware page, and view the active firmware version.
TFTP Upgrade
To upgrade the firmware on the WAP device using TFTP:
Step 1
Select TFTP as the transfer method.
Step 2
Enter a name (1 to 256 characters) for the image file in the Source File Name field, including the path to the directory
that contains the image to upload.
For example, to upload the ap_upgrade.tar image located in the /share/builds/ap directory, enter:
/share/builds/ap/ap_upgrade.tar
The firmware upgrade file supplied must be a tar file. Do not attempt to use bin files or files of other formats for the
upgrade; these types of files do not work.
The filename cannot contain the following items: spaces, <, >, |, \, : , (, ), &, ; , #, ? , *, and two or more successive
periods.
Step 3
Enter the TFTP Server IPv4 address and click Upgrade.
Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE
94
Administration
HTTP/HTTPS Upgrade

Cisco WAP125 Specifications

General

2.4 GHz	Yes
MIMO type	Multi User MIMO
Modulation	16-QAM, 64-QAM, 256-QAM, BPSK, CCK, QPSK
Number of users	64 user(s)
Networking standards	IEEE 802.3af, IEEE 802.11ac
Spread spectrum method	DSSS, OFDM
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	867 Mbit/s
Security algorithms	WPA, WPA2
Number of SSID supported	8
Supported network protocols	IPv6, NTP, HTTP, HTTPS
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	1
Output current	1 A
Output voltage	12 V
Power plug type	Type C
AC input voltage	100 - 240 V
AC input frequency	50 Hz
Placement	Desk
Certification	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC 60950-1, EN 60950-1, FCC 15.247, 15.407; RSS-210; EN 300.328, EN 301.893; AS/NZS 4268.2003; FCC 15.107 15.109, ICES-003, EN 301.489-1 -17
Product color	White
Recommended usage	Indoor
Cable lock slot type	Kensington
Antenna type	Internal
Antenna gain level (max)	5.63 dBi
Flash memory	128 MB
Internal memory	256 MB
Operating system installed	Linux
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Country of origin	China
Quantity per pack	1 pc(s)
Package depth	188.976 mm
Package width	168.91 mm
Package height	80.01 mm
Package weight	1133.98 g

Weight and Dimensions

Width	123.19 mm
Height	31.75 mm
Weight	303.91 g