Cisco WAP125 Administrator's Guide

A host name can consist of one or more labels, which are sets of up to 63 alphanumeric characters. If a host name
includes multiple labels, each is separated by a period (.). The entire series of labels and periods can be up to 253
characters long.
• Enable — Check Enable to enable the remote log server. Next, define the log severity and UDP port.
• Log Severity — Check the severities that an event must have for it to be sent to remote log server.
• UDP Port — Enter the logical port number for the syslog process on the remote host. The range is from 1 to 65535.
The default port is 514.
Using the default port is recommended. If you reconfigure the log port, make sure that the port number that you
assign to syslog is available for use.
Step 3
Click Save. The changes are saved to the Startup Configuration.
If you enable a remote log server, clicking Save activates the remote logging. The WAP device sends its kernel
messages in real-time for display to the remote log server monitor, a specified kernel log file, or other storage,
depending on your configuration.
If you disabled a remote log server, click Save to disable remote logging.
Note
View System Log
The View System Log page displays the list of system events occurring on the device. The log is cleared upon
a reboot and can be cleared by an administrator. Up to 1000 events can be shown. Older entries are removed
from the list as needed to make room for new events.
To view the system logs, select Notification > View System Log.
The following information is displayed:
• Time Stamp — The system time when the event occurred.
• Severity — The severity level of the event.
• Service — The service associated with the event.
• Description — A description of the event.
You can filter or rearrange the settings on View System Log.
Click Refresh to refresh the screen and show the most current information.
Click Clear All to clear all entries from the log.
Click Download to download all entries from the log.
Email Alert/ Mail Server/ Message Configuration
The email alert feature supports mail server configuration, message severity configuration, and up to three
email addresses to send urgent and non-urgent email alerts. Use the Email Alert to send messages to the
configured email addresses when particular system events occur.
Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE
19
System Configuration
View System Log

Cisco WAP125 Specifications

General

2.4 GHz	Yes
MIMO type	Multi User MIMO
Modulation	16-QAM, 64-QAM, 256-QAM, BPSK, CCK, QPSK
Number of users	64 user(s)
Networking standards	IEEE 802.3af, IEEE 802.11ac
Spread spectrum method	DSSS, OFDM
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	867 Mbit/s
Security algorithms	WPA, WPA2
Number of SSID supported	8
Supported network protocols	IPv6, NTP, HTTP, HTTPS
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	1
Output current	1 A
Output voltage	12 V
Power plug type	Type C
AC input voltage	100 - 240 V
AC input frequency	50 Hz
Placement	Desk
Certification	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC 60950-1, EN 60950-1, FCC 15.247, 15.407; RSS-210; EN 300.328, EN 301.893; AS/NZS 4268.2003; FCC 15.107 15.109, ICES-003, EN 301.489-1 -17
Product color	White
Recommended usage	Indoor
Cable lock slot type	Kensington
Antenna type	Internal
Antenna gain level (max)	5.63 dBi
Flash memory	128 MB
Internal memory	256 MB
Operating system installed	Linux
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Country of origin	China
Quantity per pack	1 pc(s)
Package depth	188.976 mm
Package width	168.91 mm
Package height	80.01 mm
Package weight	1133.98 g

Weight and Dimensions

Width	123.19 mm
Height	31.75 mm
Weight	303.91 g