Cisco WAP125 Administrator's Guide

Launching the Web-based Configuration Utility
Follow these steps to access the configuration utility from your computer to configure the WAP device:
1
Connect the WAP device to the same network (IP subnet) as your computer. The factory default IP address
configuration of the WAP device is DHCP. Make sure that your DHCP server is running and can be
accessed.
2
Locate the IP address of the WAP device.
a
The WAP device can be accessed and managed by using the Cisco FindIT Network Discovery Utility.
This utility enables you to automatically discover all supported Cisco devices in the same local network
segment as your computer. You can get a snapshot view of each device or launch the product
configuration utility to view and configure the settings. For more information, see http://www.cisco.com/
go/findit.
b
The WAP device is Bonjour-enabled and automatically broadcasts its services and listens for services
being advertised by other Bonjour-enabled devices. If you have a Bonjour- enabled browser, such as
Microsoft Internet Explorer with a Bonjour plug-in, or the Apple Mac Safari browser, you can find
the WAP device on your local network without knowing its IP address.
You can download the complete Bonjour for Microsoft Internet Explorer browser from Apple’s website
by visiting: http://www.apple.com/bonjour/ .
c
Locate the IP address assigned by your DHCP server by accessing your router or DHCP server. See
your DHCP server instructions for more information.
3
Launch a web browser, such as Microsoft Internet Explorer.
4
In the address bar, enter the default DHCP address and press Enter.
5
Enter the default user name and password: cisco in the Username and Password fields.
6
Click Log In. The Access Point Setup Wizard appears.
Follow the Setup Wizard instructions to finish the installation. We strongly recommend that you use the Setup
Wizard for the first installation. See Using the Access Point Setup Wizard, on page 2 for more information.
Logging Out
By default, the configuration utility logs out after 10 minutes of inactivity. See Management, on page 23 for
instructions on changing the default timeout period.
To log out, click Logout in the top right corner of the configuration utility.
Using the Access Point Setup Wizard
The first time that you log into the Access Point (or after it has been reset to the factory default settings), the
Access Point Setup Wizard appears to help you perform initial configurations. Follow these steps to complete
the wizard:
Cisco WAP125 Wireless-AC/N Dual Band Desktop Access Point with PoE
2
Getting Started
Using the Access Point Setup Wizard

Cisco WAP125 Specifications

General

2.4 GHz	Yes
MIMO type	Multi User MIMO
Modulation	16-QAM, 64-QAM, 256-QAM, BPSK, CCK, QPSK
Number of users	64 user(s)
Networking standards	IEEE 802.3af, IEEE 802.11ac
Spread spectrum method	DSSS, OFDM
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	867 Mbit/s
Security algorithms	WPA, WPA2
Number of SSID supported	8
Supported network protocols	IPv6, NTP, HTTP, HTTPS
USB 2.0 ports quantity	0
Ethernet LAN (RJ-45) ports	1
Output current	1 A
Output voltage	12 V
Power plug type	Type C
AC input voltage	100 - 240 V
AC input frequency	50 Hz
Placement	Desk
Certification	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, IEC 60950-1, EN 60950-1, FCC 15.247, 15.407; RSS-210; EN 300.328, EN 301.893; AS/NZS 4268.2003; FCC 15.107 15.109, ICES-003, EN 301.489-1 -17
Product color	White
Recommended usage	Indoor
Cable lock slot type	Kensington
Antenna type	Internal
Antenna gain level (max)	5.63 dBi
Flash memory	128 MB
Internal memory	256 MB
Operating system installed	Linux
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 85 %
Country of origin	China
Quantity per pack	1 pc(s)
Package depth	188.976 mm
Package width	168.91 mm
Package height	80.01 mm
Package weight	1133.98 g

Weight and Dimensions

Width	123.19 mm
Height	31.75 mm
Weight	303.91 g