COBHAM AVIATOR 200 - Installation Manual

To Next Page

AVIATOR 200/300/350

Installation manual

98-127093-G Cover_Installation manual AVIATOR 200-300-350.indd 1 03-07-2013 15:19:18

Main Page

Default Chapter5
- A-15
- Table of Contents7
Chapter 1 About this Manual21
- Purpose21
- Organization21
- Related Documentation22
- Precautions: Warnings, Cautions and Notes22
  - Table 1-1: List of Related Documentation22
Chapter 2 Introduction to the AVIATOR23
- General Description23
- Application31
- System Block Diagrams36
Chapter 3 Equipment Drawings43
- Introduction43
- Tt-5040A Sbu44
- TT-5038A-003 Rx Power Splitter46
  - Figure 3-3: Outline Drawing: Rx Power Splitter46
- Tt-5016A Hld47
  - Figure 3-4: Outline Drawing: TT-5016A HLD47
- Tt-3002A Lga48
  - Figure 3-5: Outline Drawing: TT-3002A LGA48
- Tt-5006A Iga49
  - Figure 3-6: Outline Drawing: TT-5006A IGA Antenna49
- TT-5621B 2-Wire Handset50
  - Figure 3-7: Outline Drawing: TT-5621B 2-Wire Handset50
- TT-5622B 2-Wire Cradle51
  - Figure 3-8: Outline Drawing: TT-5622B 2-Wire Cradle51
- SBU Trays52
- SBU Tray Connector55
  - Figure 3-12: Outline Drawing: SBU Tray Connector: ITT Cannon DPX2NA-67322-60655
- Contact Assembly: Quadrax Pin Size 5 Special56
  - Figure 3-13: Contact Assembly: Quadrax Pin Size 5 Special: ITT Cannon 244-0011-00156
  - Figure 3-14: Outline Drawing: TT-5040A-004 WLAN Antenna58
TT-5040A-004 WLAN Antenna58
- Figure 3-15: Outline Drawing: Switch Annunciator Panel59
Switch Annunciator Panel59
Chapter 4 Connectors and Pin-Out61
Tt-5040A Sbu61
- Connectors on SBU61
- SBU Maintenance Connector61
- Figure 4-1: SBU Maintenance Connector, Face View of Engaging End61
- Table 4-1: Pin-Out for SBU Maintenance Connector (Standard Ethernet)62
- SBU Rear Receptacle63
- Figure 4-2: SBU Rear Receptacle, Engaging End (Index Code: 19)63
- Figure 4-3: SBU Rear Receptacle with Pin Functions64
- Table 4-2: Pin-Out for SBU Rear Receptacle, Top Plug67
- Table 4-3: Pin-Out for SBU Rear Receptacle, Bottom Plug68
Tt-5016A Hld69
- Connectors on HLD69
- Figure 4-4: TT-5016A HLD Connector Panel69
TT-5622B 2-Wire Cradle70
- Connectors on 2-Wire Cradle70
- Figure 4-5: 2-Wire Cradle Connectors, End View of Cradle70
- Figure 4-6: TT-5622B 2-Wire Cradle Connectors, Side View of Cradle70
- 2-Wire Cradle Connector to SBU71
- Figure 4-7: 2-Wire Cradle Connector (DB9M). View: Solder Side71
- Table 4-4: Pin-Out for 9 Pin Sub-D Male Connector in TT-5622B 2-Wire Cradle71
Mating Connectors in Aircraft72
- Connection with SBU72
- Table 4-5: Mating Connectors in Aircraft for SBU72
Chapter 5 Installation73
General Installation Information73
- Overview73
- Table 5-1: Installation Kits, Contact Information73
- Minimum System Components74
- Figure 5-1: AVIATOR 200 Minimum System (Example with LGA TT-3002A and GPS Antenna)74
Mounting Considerations75
- Overview75
- Tt-5040A Sbu75
- Tt-5016A Hld75
- Satcom Antenna76
- Table 5-2: Navigational Input for Satcom Antennas76
- TT-5040A-004 WLAN Antennas79
  - Figure 5-2: Mounting Two WLAN Antennas for Optimum Performance79
- Electrical Installation and Wiring80
- Recommended Cables119
- Activation of Airtime Services122
  - Cables for Discrete Signals122
Chapter 6 Configuration of the AVIATOR 200/300/350 System125
- Figure 6-1: Line of Sight When Communicating with the Satellite125
- Basic Configuration of the SBU126
- Configuration Tasks126
- Tool for Setup and Use: Built-In Web Interface130
- The Dashboard136
- The Phone Book139
  - View and Edit the Mobile and Additional Numbers139
  - Figure 6-14: Web Interface: Phone Book, Mobile Numbers (Example, with Multi-Voice)140
To Set up the Interfaces141
- The SETTINGS Page141
- Select the Preferred BGAN Satellite142
- Figure 6-15: Web Interface: Settings, Satellite Selection142
- Configure the LAN Interface143
- Figure 6-16: SBU IP Addresses: Local and Global IP Addresses, Default143
- Figure 6-17: Web Interface: Settings, LAN144
- Figure 6-18: Web Interface: Settings, LAN, Port Forwarding145
- WLAN Interface (Option)146
- Figure 6-19: Web Interface: Settings, WLAN (Example: AVIATOR 350)146
- Configure the Phone/Fax Interface (2-Wire)148
- Figure 6-20: Web Interface: Settings, Phone/Fax148
- Configure the ISDN Interface149
- Figure 6-21: Web Interface: Settings, ISDN149
- Set the Common Interface Settings151
- Figure 6-22: Web Interface: Settings, Common151
- Set up Call Services152
- Figure 6-23: Web Interface: Settings, Common, Call Forward153
- Figure 6-24: Web Interface: Settings, Common, Call Barring154
- Figure 6-25: Web Interface: Settings, Common, Call Waiting155
- Figure 6-26: Web Interface: Settings, Common, Line Identification156
- Figure 6-27: Web Interface: Settings, Common, Closed User Group157
- Manage AVIATOR Wireless Handsets158
- Figure 6-28: Web Interface: Settings, IP Handsets159
- Figure 6-29: Web Interface: Settings, IP Handsets, Call Settings160
- Configure the Discrete I/O Interfaces161
- Figure 6-30: Web Interface: Settings, Discrete I/O (Without SB-Safety Voice)162
- Set the System Type163
- Figure 6-31: Web Interface: Settings, Discrete I/O (with SB-Safety Voice)163
- Figure 6-32: Web Interface: Settings, System Type164
- Table 6-2: Changing the System Type, Use of Reset Button165
- Configure RF Settings167
- Figure 6-33: Web Interface: Settings, RF Settings167
- Set up the Navigational Input168
- Table 6-3: Navigational Input for System Types and Satcom Antennas168
- Figure 6-34: Web Interface: Settings, External Systems (AVIATOR 350 with TT-5006 Antenna)169
- Calibrate the NRS Magnetometer in the TT-5006A IGA170
- Figure 6-35: Web Interface: Settings, External Systems, Magnetometer Calibration171
- Table 6-4: Evaluation of the Magnetometer Calibration Score172
- Table 6-5: Magnetometer Calibration: Error Messages at Failing Start Procedure174
- Table 6-6: Magnetometer Calibration: Error Messages at Failing Stop Procedure174
- Set up CMU/ACARS (Option)175
- Table 6-7: Satcom Antennas in AVIATOR Systems Supporting CMU175
- Figure 6-36: Web Interface: CMU/ACARS176
- Enable System Options with FLEX Keys177
- Figure 6-37: Web Interface: Settings, FLEX (Example)177
- Tracking178
- Figure 6-38: Web Interface, Settings, Tracking178
- SB-Safety Voice (Option)179
LAN/WLAN Network Users181
- Introduction181
- Figure 6-42: Overview over Network User Groups and Traffic Flow Filters181
- Set up the Network User Groups183
- Figure 6-43: Web Interface: Settings, LAN, Network User Groups183
- Figure 6-44: Web Interface: Settings, LAN, Network User Groups, Edit184
- Manage Network Devices186
- Figure 6-45: Web Interface: Settings, LAN, Network Devices186
- The Network Classification Table187
- Figure 6-46: Web Interface: Settings, LAN, Network Classification Table188
- Figure 6-47: Web Interface: Settings, LAN, Network Classification Table, Edit or Add188
- Definitions for Network Terms189
- Figure 6-48: Web Interface: Settings, LAN, Network Classification Table, Change Priority189
NAT (Network Address Translation)190
- Start and Stop any Data Session190
- Figure 6-49: NAT (Network Address Translation)190
- Figure 6-50: Web Interface: Connect, to Start and Stop Data Sessions (Example)190
- Establish a Pppoe Connection191
- Figure 6-51: Example for Pppoe Connections191
- Figure 6-52: Web Interface, Settings, LAN, Pppoe192
- Table 6-8: Pppoe Connection, Service Names and Descriptions193
- Table 6-9: Pppoe Connection, Service Names and Descriptions for Custom APN193
- To Set up Static Routing194
- Figure 6-53: Web Interface, Settings, LAN, Static Route194
- Figure 6-54: Web Interface, Settings, LAN, Static Route, Add194
- SNMP Interface195
Administration195
- Protect the SBU against Unintended Configuration Changes195
- Access the Administration Settings196
- Figure 6-55: Web Interface: Administration196
- Figure 6-56: Web Interface: Administration, Change Administrator Logon197
- Figure 6-57: Web Interface: Administration, Reset Administrator Password198
- Save and Load a Configuration199
- Figure 6-58: Web Interface: Administration, Saving a Configuration File199
- Figure 6-59: Web Interface: Administration, Saving a Configuration File200
- Call Charges201
- Figure 6-60: Web Interface: Administration, Call Charges201
- Log Handling202
- Data Limits202
- To Use Profiles202
- Figure 6-61: Web Interface: Administration, Log Handling202
- Figure 6-62: Web Interface, Administration, Profiles, Example: Standard203
- Figure 6-63: Web Interface. Administration, Profiles, Select Profile (Example AVIATOR 350)204
- To Use Traffic Flow Filters206
- Figure 6-64: Traffic Flow Filters to Filter Traffic Types206
- Figure 6-65: Web Interface: Administration, Traffic Flow Filters207
- Figure 6-66: Web Interface: Administration, Traffic Flow Filters, New Entry207
- Figure 6-67: Web Interface: Example of Two Traffic Flow Filters208
- SIM Card Access Protection: SIM PIN and SIM Lock209
- Figure 6-68: Web Interface, Administration, SIM PIN209
- Figure 6-69: Web Interface, Administration, SIM LOCK210
- Set up User Permissions211
- Figure 6-70: Web Interface: Administration, User Permissions211
- Remote Management213
- Figure 6-71: Web Interface: Administration, Remote Management213
- Remote Activation of a Connection Using SMS214
- Link Monitoring (Swiftbroadband Only)214
- Figure 6-72: Web Interface: Administration, Link Monitoring214
- Restricted Dialing215
- Multi-Voice (Option)215
- Table 6-10: Multi-Voice, Number of Calls215
- Figure 6-73: Multi-Voice, Call Type Groups (Example)217
- Figure 6-74: Multi-Voice, Example of Directly Assigned Handsets (Example)217
- Figure 6-75: Multi-Voice, Example of Unassigned Handsets218
- Figure 6-76: Multi-Voice, Example for a Configuration with Cockpit Reserve218
- Figure 6-77: Web Interface: Administration, Multi-Voice219
- Figure 6-78: Web Interface: Phone Book, Mobile Numbers (Example, Multi-Voice)220
- Figure 6-79: Web Interface: Settings, IP Handsets, Call Settings (with Multi-Voice, Example)221
Site Map222
- Figure 6-80: Web Interface: Site Map222
Configuration of 3Rd Party Phone Systems223
- Sigma 7 Setup223
- ICG DECT Cordless Handset Setup223
AVIATOR 200/300/350 System Ready for Use224
- Figure 6-81: AVIATOR 200/300/350 System224
Chapter 7 Maintenance and Troubleshooting225
Continued Airworthiness225
- General225
- Instructions225
Get Support: HELPDESK227
- Airtime Support227
- System Support227
- Help Desk and Diagnostic Report227
- Figure 7-1: Web Interface: Help Desk227
- Figure 7-2: Web Interface: Help Desk, Extended Status228
Software Update229
- SBU Software Update230
- Figure 7-3: Web Interface: Settings, Upload231
- Verify the Software Update232
- Figure 7-4: Software Identification on the SBU Label, Level D and Level E232
To Exchange Lrus233
- Time Consumption233
- Tools233
- Removal and Re-Installation of the SBU233
- Figure 7-5: Exchanging an LRU (Example)233
- Figure 7-6: Pull out the LRU234
- Figure 7-7: Attach CM to the Airframe234
Troubleshooting235
- Status Signalling235
- Status Signalling with Leds236
- Table 7-1: Function of the SBU Power LED236
- Table 7-2: Function of the SBU Logon LED236
- Table 7-3: Function of the SBU Fail/Pass LED236
- Figure 7-8: Function of the Leds on the Front Maintenance Connector237
- IP Reset (Default) Button238
- Figure 7-9: IP Reset (Default) Button on SBU Front238
- Table 7-4: How to Reset the IP Address or the Terminal Software to Default Settings239
- View the Event List, Event Log and Extended Status240
- Figure 7-10: Web Interface: Help Desk, Event List240
- Self Test241
- Figure 7-11: Web Interface: Help Desk, Self Test241
- Initial Troubleshooting242
- Table 7-5: Initial Troubleshooting242
Return Units for Repair243
Disposal of Electrical and Electronic Equipment244
- Appendices245
Appendix A Equipment Specifications247
Introduction247
AVIATOR 200/300/350 System Components248
- TT-5040A Swiftbroadband Unit (SBU248
  - Table A-1: Equipment Specifications for TT-5040A SBU248
- TT-5040A-001 Configuration Module (CM) for SBU249
  - Table A-2: Equipment Specifications for TT-5040A-001 CM249
- TT-5016A High Power Amp./Low Noise Amplifier/Diplexer (HLD250
  - Table A-3: Equipment Specifications for TT-5016A HLD250
- TT-5040A-004 WLAN Antenna251
- TT-5038A-003 Rx Power Splitter251
  - Table A-4: Equipment Specifications for WLAN Antenna251
  - Table A-5: General Specifications for Rx Power Splitter251
AVIATOR 200/300/350 Handsets and Cradles253
- TT-5621B 2-Wire Handset253
- TT-5622B 2-Wire Cradle253
  - Table A-6: Equipment Specifications for 2-Wire Handset253
  - Table A-7: Equipment Specifications for 2-Wire Cradle253
Appendix B DO-160 Specifications255
General255
- Certifying Agency255
- Environmental Qualification Forms255
AVIATOR 200/300/350 System Components256
- Swiftbroadband Unit (SBU256
  - Table B-1: Environmental Qualification Form for SBU256
- Configuration Module (CM) for SBU258
- High Power Amplifier/Low Noise Amplifier/Diplexer (HLD258
  - Table B-2: Environmental Qualification Form for HLD258
- Rx Power Splitter260
  - Table B-3: RTCA/DO-160D Change Numbers, Tx Coupler and Rx Power Splitter260
  - Table B-4: Environmental Qualification Form for Tx Coupler and Rx Power Splitter260
AVIATOR 200/300/350 Handsets and Cradles262
- 2-Wire Handset and 2-Wire Cradle262
  - Table B-5: Environmental Qualification Form for 2-Wire Handset and Cradle262
Appendix C System Messages265
Types of Messages265
List of Events266
- Table C-1: SBU Events266
Restrictions in WLAN Use277
Countries Where the "US" Country Code Applies278
- Table D-1: Countries that Accept the Country Code "US" for WLAN Indoor Operation278
Appendix D WLAN Country Codes279
Appendix E References279
Applicable Standards279
- E.1 Applicable Standards279
Appendix F TT-5019A Iridium Band Reject Filter281
Introduction281
- System Block Diagram281
- Figure F-1: System Configuration with TT-5019A Iridium Band Reject Filter (1281
- F.1 Introduction281
Equipment Drawing282
- Figure F-2: Outline Drawing: TT-5019A Iridium Band Reject Filter282
- F.2 Equipment Drawing282
Installation283
- Mounting Considerations283
- Figure F-3: Wiring TT-5019A Iridium Band Reject Filter283
- F.3 Installation283
- Electrical Installation and Wiring284
Configuration284
Specifications284
- Table F-1: Distance to Iridium284
- Table F-2: Equipment Specifications for TT-5019A Iridium Band Reject Filter284
- Table F-3: Environmental Qualification Form for Iridium Band Reject Filter285
- F.6 DO-160 Specifications285
Appendix G Terminal Commands287
Get Started287
- Connect to the SBU287
- G.1 Get Started287
Commands for Troubleshooting the SBU288
- Monitor the ARINC Interfaces on the SBU288
- Description of the Status Report289
Introduction293
- Connect to the WLAN Interface293
- Set up a SIP Profile293
- H.1 Introduction293
Appendix H SIP Setup for Wifi-Enabled Phones295
Glossary295
Index299

COBHAM AVIATOR 200 - Installation Manual

Table of Contents

Other manuals for COBHAM AVIATOR 200

Related product manuals