Contec CMS8000 Manual

-
-
-
- 33 -
-
-
-
Physiological alarm is displayed in the Physiological Alarm area. Most of technical alarms are displayed
in the Technical Alarm area. Technical alarms related to NIBP measurement are displayed in the NIBP
Technical Alarm area at the bottom of NIBP parameter area.
N
N
N
N ote
ote
ote
ote
The
The
The
The Physiological
Physiological
Physiological
Physiological Alarm
Alarm
Alarm
Alarm area
area
area
area is
is
is
is on
on
on
on the
the
the
the upper
upper
upper
upper right
right
right
right part
part
part
part of
of
of
of the
the
the
the screen.
screen.
screen.
screen. The
The
The
The Technical
Technical
Technical
Technical Alarm
Alarm
Alarm
Alarm area
area
area
area
is
is
is
is to
to
to
to the
the
the
the left
left
left
left side
side
side
side of
of
of
of the
the
the
the Physiological
Physiological
Physiological
Physiological Alarm
Alarm
Alarm
Alarm area.
area.
area.
area.
N
N
N
N ote
ote
ote
ote
The
The
The
The concrete
concrete
concrete
concrete presentation
presentation
presentation
presentation of
of
of
of each
each
each
each alarm
alarm
alarm
alarm prompt
prompt
prompt
prompt is
is
is
is related
related
related
related to
to
to
to the
the
the
the alarm
alarm
alarm
alarm level.
level.
level.
level.
Screen
Screen
Screen
Screen Display
Display
Display
Display
When an alarm occurs,the parameter value triggering the alarm will become red . “ * ” signal appears on
the screen indicating the occurrence of alarm. Red “ *** ” indicates high-level alarm, yellow “ ** ” indicates
medium-level alarm, and yellow “ * ” indicates low-level alarm. Technical alarm will not prompts “ * ” signal.
Lamp
Lamp
Lamp
Lamp light
light
light
light
The high/medium/low-level alarms are indicated by the system in following different visual ways:
Alarm
Alarm
Alarm
Alarm level
level
level
level Visual
Visual
Visual
Visual prompt
prompt
prompt
prompt
High Alarm indicator flashes in red with high frequency.
Medium Alarm indicator flashes in yellow with low frequency.
Low Alarm indicator lights on in yellow.
Alarm
Alarm
Alarm
Alarm Sound
Sound
Sound
Sound
The high/medium/low-level alarms are indicated by the system in following different audio ways:
Alarm
Alarm
Alarm
Alarm level
level
level
level Audio
Audio
Audio
Audio prompt
prompt
prompt
prompt
High
Mode is “ DO-DO-DO------DO-DO, DO-DO-DO------DO-DO ” , which is
triggered once every 8 seconds.
Medium Mode is “ DO-DO-DO ” , which is triggered once every 8 seconds.
Low Mode is “ DO- ” , which is triggered once every 8 seconds.
N
N
N
N ote
ote
ote
ote
When
When
When
When alarms
alarms
alarms
alarms of
of
of
of different
different
different
different levels
levels
levels
levels occur
occur
occur
occur at
at
at
at the
the
the
the same
same
same
same time,
time,
time,
time, the
the
the
the monitor
monitor
monitor
monitor prompts
prompts
prompts
prompts the
the
the
the one
one
one
one of
of
of
of the
the
the
the
highest
highest
highest
highest level.
level.
level.
level.
Alarm
Alarm
Alarm
Alarm Setup
Setup
Setup
Setup
The setup of the alarms can be realized in the alarm menu.
Press the “ ALARM SETUP ” button on the SYSTEM SETUP menu to call up “ ALARM SETUP ” menu
(default menu) as shown below.

Contec CMS8000 Specifications

General

Category	Medical Equipment
Device Name	Contec CMS8000
Type	Patient Monitor
ECG Lead Mode	3-lead or 5-lead
Resolution	800 x 600
Power Supply	AC 100-240V, 50/60Hz
Battery	Rechargeable lithium battery
Operating Temperature	5°C to 40°C
Storage Temperature	-20°C to 55°C
Display	TFT LCD
Screen Size	12.1 inches
Parameters	ECG, RESP, NIBP, SpO2, TEMP, PR
Interface	Ethernet, Nurse call
Humidity	15% to 95% non-condensing
Battery Life	Approximately 4 hours