Curtis 1297 - Page 116

Curtis PMC 1297 Manual
A-19
APPENDIX A: GLOSSARY
HYD THRTL MAX OEM 60 100 90 percent page 53
HYD THRTL TYPE OEM (see sidebox†) 2 — page 51
INT BRAKE C/L OEM 50 RATED CURRENT*
1
RC*
1
amps page 27
INT BRAKE DLY OEM 0.0 30.0 2.0 seconds page 27
INT BRAKE RATE OEM 0.0 3.0 0.1 seconds page 27
INT OVERRIDE OEM OFF — page 31
LOAD COMP OEM 0.0 25.0 0.0 percent page 32
LOAD HOLD DLY OEM 0.0 1.0 0.5 seconds page 50
LV ACCEL OEM 0.0 3.0 0.1 seconds page 49
LV CHECK OEM ON — page 50
LV DECEL OEM 0.0 3.0 0.1 seconds page 50
LV DITHER OEM 0 100 0 percent page 49
LV MAX C/L OEM LV MIN C/L 3.0 1.0 amps page 49
LV MIN C/L OEM 0.0 LV MAX C/L 1.0 amps page 49
MAIN CONT DIAG OEM ON — page 57
MAIN CONT INT OEM ON — page 57
MAIN OPEN DLY OEM 0 40 0 seconds page 57
MAX SPEED, M1-M2 OEM CREEP SPEED 100 100 percent page 31
MUX ENABLE OEM OFF — page 58
NO LOAD C/L OEM 0 PUMP C/L 0 amps page 46
NO LOAD SPEED OEM 0 100 100 percent page 46
POT LOW CHECK OEM OFF — page 40
PUMP ACCEL OEM 0.1 3.0 0.1 seconds page 47
PUMP BDI L/O OEM OFF — page 48
PUMP BDI WARN OEM OFF — page 48
PUMP C/L OEM 25 RATED CURRENT*
3
RC*
3
amps page 46
PUMP DECEL OEM 0.1 3.0 0.1 seconds page 47
PUMP LOCK C/L OEM 25 RC*
3
+50 RC*
3
amps page 48
PUMP LOCK DLY OEM 0.1 25.0 0.5 seconds page 48
PUMP MAX SPEED OEM 0 100 100 percent page 46
RESTRAINT OEM FIELD MIN RATED CURRENT*
2
5.0 or 8.0 amps page 27
SEQUENCING DLY OEM 0.0 3.0 0.1 seconds page 57
SRO OEM 0 3 0 — page 45
TAPER RATE OEM 1 20 10 — page 26
THROTTLE DB OEM 0 40 10 percent page 34
THROTTLE DECEL OEM 0.1 1.0 0.3 seconds page 26
THROTTLE MAP OEM 20.0 80.0 50.0 percent page 38
THROTTLE MAX OEM 60 100 90 percent page 36
THROTTLE TYPE OEM (see sidebox††) 2 — page 33
VARIABLE BRAKE OEM ON — page 28
VARIABLE LIFT OEM OFF — page 56
VARIABLE LOWER OEM OFF — page 56
1297 DEFAULT MIN MAX DEFAULT DESCRIPTION
PARAMETER ACCESS VALUE VALUE SETTING UNITS IN
MANUAL
Table D-1, continued
D-2
APPENDIX D: PROGRAMMABLE PARAMETERS
†† Traction
throttle
types:
1=5kΩ–0
2=0–5V
3=0–5kΩ
4=wigwag
† Hydraulic
throttle
types:
2=0–5kΩ
4=0-5V
*
3
The rated armature current for the pump motor depends on the controller model:
1297-22XX (200 amps), 1297-23XX (200 amps), 1297-24XX (300 amps);
the default setting is the maximum value.